Xerox DocuPrint P14 Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 133

background image

Precautions

Appendix D: Printer Options

❖

D-3

Precautions

DISCONNECT THE POWER CORD:
Never remove the printer control board
while the printer is plugged in.

To avoid the possibility of electrical
shock, always disconnect the power cord
when installing or removing ANY internal
or external printer option.

DISCHARGE STATIC ELECTRICITY:
The control board and internal printer options
(SIMMs, PostScript, Serial/LocalTalk interface)
are sensitive to static electricity. Before
installing or removing an internal option,
discharge static electricity from your body by
touching something metal, such as the metal
back plate on any device plugged into a
grounded power source. If you walk around
before finishing the installation, again
discharge any static electricity.

«
...
121
122
123
124
125
...
»

Содержание DocuPrint P14






































































































































Отзывы:

Нет отзывов

Похожие инструкции для DocuPrint P14

Бренд: NCR Страницы: 5

Бренд: Samsung Страницы: 549

Бренд: Oki Страницы: 320

Бренд: Lexmark Страницы: 59

PAPERANG MonoSnap Lite

Бренд: Xiamen Страницы: 7

8437477 - EasyShare ESP 9 All-In-One Printer

Бренд: Kodak Страницы: 143

Бренд: Oki Страницы: 72

Бренд: MAC TOOLS Страницы: 2

Бренд: Oki Страницы: 204

Бренд: Triumph Adler Страницы: 4

Бренд: Oki Страницы: 246

Бренд: Canon Страницы: 76

DLQ-3000 Minerva+

Бренд: Epson Страницы: 189

Бренд: Epson Страницы: 223

Бренд: Epson Страницы: 228

DFX-8500 - Impact Printer

Бренд: Epson Страницы: 245

Бренд: Epson Страницы: 262

Disc producer PP-100N Security

Бренд: Epson Страницы: 153

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды