Xerox DocuPrint N4525 Скачать руководство пользователя страница 91

Страница: 91 / 380

Volume 1 / Print Engine - Error Codes & Messages

RAP 1-20

Error Code E1-3

Paper Jam

Clear Area A

There is a paper jam between the Fuser Exit Sensor and the Face Up Exit Sensor.

Logic Control on the Print Engine Controller Board sensed the Face Up Exit Sensor

was not actuated within the specified time since the Fuser Exit Sensor was actuated

Table 1-48 Error Code E1-3 Paper Jam Clear Area A

Step

Actions and Questions

Yes

OFFSET UNIT INSPECTION

1. Remove the Fuser Cover (RRP 1-1).
2. Check the Offset Unit for lodged scraps paper or

damage.

Is the Offset Unit clean and undamaged?

Go to step 2

Clean or
replace the
Offset Unit
Assembly
(RRP 1-54)

FACE UP CLUTCH TEST

NOTE: The Duplex Unit must be installed for this test.

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Output Test /

Duplex Unit / Invert Clut. CCW.

3. Press [4] to start, clutch will actuate for 2 seconds,

then release.

4. Hand rotate (counter clockwise) the Main Motor.

Do the Offset Rollers rotate?

Go to step 3

Replace the
Offset Unit
Assembly
(RRP 1-54)

FACE UP EXIT SENSOR TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Input Test / IOT

Unit / FaceUp Exit Sen.

3. Press [4] to start, [0] to stop.
4. Insert, then remove, a sheet of paper into the Face Up

Exit Sensor actuator.

Does the Control Panel display "with paper"
when you insert the paper into the Face Up Exit
Sensor, and "without paper" when you remove
the it?

Go to step 4

Replace the
Face Up Exit
Sensor (RRP
1-63)

DUPLEX EXIT GATE SOLENOID TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Output Test /

Duplex Unit / Exit Gate Sol.

3. Press [4] to test the Duplex Exit Gate Solenoid

function. The Duplex Exit Gate Solenoid will actuate
for two seconds, then release.

Does the Exit Gate Solenoid actuate when you
run the Output Test?

Go to step 5

Replace the
Exit Gate
Solenoid
(RRP 1-56)

PRINT ENGINE CONTROLLER BOARD
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 6

Problem
solved

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды