Xerox DocuPrint N4525 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 75

Volume 1 / Print Engine - Error Codes & Messages

1

-

53

RAP 1-7

Error Code U3-5

Laser Failure

Power Off/On

There is a problem with the Laser Scanner.

Logic Control on the Print Engine Controller Board detected that the Laser Scanner

Motor has not come up to full speed within the specified time.

Table 1-35 Error Code U3-5 Laser Failure Power Off/On

Step

Actions and Questions

Yes

No

1

RESET

1. Switch off printer main power.
2. Wait one minute.
3. Switch on printer main power.

Does the U3-5 error code appear?

Go to step 2

Suspect an
intermittent
problem with
the Print
Engine
Controller
Board, the
Laser
Scanner
Motor, the
SOS Sensor,
or the
connectors
and wiring
linking these
components.

2

LASER SCANNER MOTOR TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Output Test / IOT

Unit / ROS Motor On to check the Laser Scanner
Motor function.

3. Press [4] to start, [0] to stop.

Does the Laser Scanner Motor run when you
start the test?

Go to step 4

Go to step 3

3

LOW VOLTAGE POWER 24VDC
CHECK

Measure the voltage between J400-8 (on the Print
Engine Controller Board) and frame ground.

Is there +24VDC between J400-8 and frame
ground?

Replace the
Laser
Scanner
Assembly
(RRP 1-47)

Replace the
Low Voltage
Power Supply
Assembly
(RRP 1-67)

4

PRINT ENGINE CONTROLLER BOARD
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 5

Problem
solved

5

The following printer components and areas are
associated with this specific problem. One or more of
these components or areas may have failed partially or
completely. If you cannot isolate this problem using the
steps in this Repair Analysis Procedure, replace each
component or troubleshoot each area listed below, one at
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

«
...
73
74
75
76
77
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды