manualshive.com logo in svg

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Поделиться
Скачать
Xerox DocuPrint N4525 Скачать руководство пользователя страница 66

1-

44

DocuPrint N4525 Network Laser Printer - Service Guide

System Controller Error Codes

The following error codes are considered to be Power-On Boot Codes.

Most Repair Analysis Procedures assume there is no malfunction in the System Controller 
Board.  If you are unable to correct a problem using the previous error code table, it is 
recommended that you now check the System Controller Error Blink Codes per the table 

below.  In some instances, the Control Panel Display may not be sufficiently functional to 
accurately show error codes/messages.  Before replacing the System Controller, please 

refer to this table for additional help in troubleshooting.

The System Controller Board is programmed to display simple error codes by means of a 
single red LED (CR 1) near the connecter edge of the board.  The LED blinking pattern 

will indicate various detected failures connected with the board and/or accessories 
installed on the board.  The System Controller Error Code Table below will help you 

pinpoint the fault.  If all else fails, replace the System Controller Board.

Table 1-28 System Controller Error Code Table

Control Panel Message

LED # Blinks,
Followed by 1 
sec.  Off

Comment

0001 - ESS

1

System Controller Board major failure.  Replace 
System Controller Board.  Go to RRP 1-73.

0001 - BASE RAM

2

System Controller Board RAM failure.  Replace 
System Controller Board.  Go to RRP 1-73.

0001 - BASE ROM

3

System Controller Board boot ROM.  Replace 
System Controller Board.  Go to RRP 1-73.

0001 - ASIC

4

System Controller Board ASIC failure.  Replace 
System Controller Board.  Go to RRP 1-73.

0001 - TIMER

4

System Controller Board Timer failure.  Replace 
System Controller Board.  Go to RRP 1-73.

0001 - PWPM

5

System Controller Board PWPM failure.  Replace 
System Controller Board.  Go to RRP 1-73.

0001 - DMA

5

System Controller Board DMA failure.  Replace 
System Controller Board.  Go to RRP 1-73.

0001 - COMM or
0001 - USB

6

System Controller Board parallel or USB port failure.  
Replace System Controller Board.  Go to RRP 1-73.

1000 - IOT

8

System Controller - IOT (Print Engine) 

handshake failure.  Remove and reinstall the 
System Controller Board (RRP 1-73)

Replace the System Controller Board (RRP 

1-73)

Replace the Print Engine Controller Board 

(RRP 1-72)

0010 - DISK

9

Hard disk failure.

Format Hard Disk (Call Technical Support for 

assistance)

Replace the Hard Disk (Instructions supplied 

with the replacement hard disk)

Replace the Print Engine Controller Board 

(RRP 1-73)

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды