Xerox DocuPrint N4525 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 43

Volume 1 / Print Engine - General Information

1

-

21

Paper Output Devices

The printer uses the following paper output/paper size combinations:

Face Down Tray (standard)

The Face Down Tray is the standard output tray for the printer. Paper is transported out of

the printer face down onto the printer Top Cover. This tray holds up to 500 sheets of 20 lb.
paper, and comes equipped with Full Stack detection. When the optional Finisher is

installed on the printer, the maximum paper stack in the Face Down Tray is reduced to
300.

Offset Unit (standard)

The Offset Unit is attached above the Fuser on the print engine. Each print job is offset 10

mm

from the last, then placed in the Face Down Tray.

Paper size supported by the Offset Unit:

Duplex Unit (option)

The optional Duplex Unit for the printer provides duplex printing for 64 gsm~105 gsm

paper fed from Trays 1 through 5. The minimum paper size recommended for Duplex
feed is B5 LEF or Executive. The maximum paper size recommended for Duplex feed is

A3 SEF or 11" x 17" SEF.

Face Up Tray (option)

The optional Face Up Tray attaches to the left side of the printer. Paper is transported out

of the printer face up onto the Face Up Tray. The Tray holds up to 200 sheets of 20 lb.
paper. There is no Full Stack detection for this tray.

Finisher

The optional Finisher provides for hole punching (3-hole or 4-hole), compiling, stapling

and stacking of finished print jobs. The stacker will hold up to 3,000 sheets of 20 lb.
paper.

Table 1-15 Offset Unit Paper Sizes

Paper

Letter SEF (20lb) - 216

mm

x 279 mm (8.5 x 11 in.)

Legal 13" SEF (20lb) - 216 mm x 330 mm (8.5 x 13 in.)

Legal 14" SEF (20lb) - 216 mm x 356 mm (8.5 x 14 in.)

A4 SEF (RX80) - 210 mm x 297 mm (8.27 x 11.71 in.)

Ledger - 297 mm x 432 mm (11.71 x 17 in.)

A3 - 297 mm x 420 mm (11.71 x 16.55 in.)

«
...
41
42
43
44
45
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды