Xerox DocuPrint N4525 Скачать руководство пользователя страница 139

Страница: 139 / 380

Volume 1 / Print Engine - Troubleshooting

117

RAP 1-62

Black Prints

PROBLEM

The entire image area is black. There is no image visible on
the page.

THE PRINTER DISPLAYS NO ERROR CODE.

Fig 1-17 Black Prints

Table 1-86 Black Prints

Step

Actions and Questions

Yes

CONTROLLER OR HOST SOFTWARE
ISOLATION

1. Generate a Grid Test Print.

Is the test print image normal?

Replace the
System
Controller
Board (RRP
1-73) or
reload the
host software

Go to step 2

LASER PRINT (EP) CARTRIDGE
REPLACEMENT

Install a new Laser Print (EP) Cartridge.

Is there a normal image on the paper?

Problem
solved

Go to step 3

IMAGE DEVELOPMENT INSPECTION

1. Remove the Rear Cover (RRP 1-5).
2. Generate a Grid Test Print and switch OFF printer

power halfway through the print cycle.

3. Open the Left Upper Cover.
4. Open the Drum Shutter.
5. Hand rotate (counter clockwise) the Drum Drive Motor

flywheel to advance the Drum far enough so you can
see the developed image area on the Drum before it
reached Transfer.

Is the image on the drum completely
developed; with sharp, black, easily read areas
and clear, white areas?

Replace the
Bias Transfer
Roller
Assembly

Go to step 4

S4525-08

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды