Xerox DocuPrint N4525 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 113

Volume 1 / Print Engine - Error Codes & Messages

1

-

91

RAP 1-36

Error Code H1-1

Insert Tray 1

There is a Lift Up problem with Tray 1.

Logic Control on the Print Engine Controller Board sensed that Tray 1 was not raising

into position in Feeder 1.

Table 1-64 Error Code H1-1 Insert Tray 1

Step

Actions and Questions

Yes

No

1

Tray 1 LIFT MOTOR TEST

1. Remove the Rear Cover (RRP 1-5).
2. Load paper into Tray 1 and install Tray 1 into Feeder 1.
3. Enter Diagnostics Mode.
4. From the Main Menu, select Comp Output Test / IOT

Unit / Tray 1 Lift Mot to check the Tray 1 Lift Motor.

5. Press [4] to start, Tray 1 Lift Motor should run two

seconds, then stop.

Does the Tray 1 Lift Motor run when you start
the test?

Go to step 2

Replace Tray
1 Lift Motor
(RRP 1-9)

2

Tray 1 CHECK

Slowly side Tray 1 out of Feeder 1.

Can you hear the Tray 1 bottom plate drop as
you slide the Tray out of the Feeder?

Go to step 2

Replace Tray
1 with a new
one

3

Tray 1 LEVEL SENSOR TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Input Test / IOT

Unit / Tray 1 Level to check the Tray 1 Level Sensor.

3. Press [4] to start, [0] to stop.
4. Repeatedly open and close Tray 1.

Does the Control Panel display “Up” when you
open the Bin, and “Down” when you close the
Bin?

Go to step 4

Replace the
Tray 1 Level
Sensor

4

PRINT ENGINE CONTROLLER BOARD
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 5

Problem
solved

5

The following printer components and areas are
associated with this specific problem. One or more of
these components or areas may have failed partially or
completely. If you cannot isolate this problem using the
steps in this Repair Analysis Procedure, replace each
component or troubleshoot each area listed below, one at
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

«
...
111
112
113
114
115
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды