Xerox DocuPrint N4525 Скачать руководство пользователя страница 111

Страница: 111 / 380

Volume 1 / Print Engine - Error Codes & Messages

RAP 1-35

Error Code C9-3

Paper Jam

Reset
ENV/Bypass

There is a paper jam between the Multi-sheet Bypass Feeder and the Registration

Sensor.

Logic Control on the Print Engine Controller Board sensed that when paper was fed

from the Multi-sheet Bypass Feeder, the Registration Sensor did not actuate within

the specified time after the Multi-sheet Bypass Feeder Feed Clutch was actuated.

Table 1-63 Error Code C9-3 Paper Jam Reset ENV/Bypass

Step

Actions and Questions

Yes

PAPER INSPECTION

Inspect the paper that is loaded in the Multi-sheet Bypass
Feeder.

Is the paper loaded in the Multi-sheet Bypass
Feeder wrinkled or damaged?

Replace the
paper with
new paper

Go to step 2

PAPER PATH INSPECTION

Inspect the paper path for paper scraps or foreign objects
that could cause a paper jam.

Is the paper path clear?

Go to step 3

Clear the
paper path

MULTI-SHEET BYPASS FEEDER FEED
ROLLER INSPECTION

1. Run a Test Print, feeding from the Multi-sheet Bypass

Feeder.

2. Observe the paper in the Multi-sheet Bypass Feeder

Bin.

Is the paper partially fed out of the Multi-sheet
Bypass Feeder Bin?

Replace the
Multi-sheet
Bypass
Feeder Feed
Roller (RRP
1-30), Pick
Roller (RRP
1-31), and
Multi-sheet
Bypass
Feeder Pad
(RRP 1-33)

Go to step 4

MULTI-SHEET BYPASS FEEDER DRIVE TEST

1. Remove the Rear Cover (RRP 1-5) so you can

observe the Main Drive Assembly and the Multi-sheet
Bypass Feeder Drive Gear Assembly.

2. Enter Diagnostics Mode.
3. From the Main Menu, select Comp Output Test / IOT

Unit / Main Motor On to actuate the Main Motor to
check the Multi-sheet Bypass Feeder Drive Assembly.

4. Press [4] to start, [0] to stop.

Does the Main Drive Assembly rotate the
Multi-sheet Bypass Feeder Drive Gear
Assembly?

Go to step 5

Replace the
Multi-sheet
Bypass
Feeder
Assembly
(RRP 1-25)

MULTI-SHEET BYPASS FEEDER CLUTCH TEST

Run Diagnostic Mode - Output Multi-sheet Bypass
Feeder Feed Clutch.

Did the Multi-sheet Bypass Feeder Feed
Clutch actuate?

Go to step 6

Replace the
Multi-sheet
Bypass
Feeder Feed
Clutch (RRP
1-29)

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды