Xerox DocuPrint N4525 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 380

Xerox DocuPrint N4525 Скачать руководство пользователя страница 109

Volume 1 / Print Engine - Error Codes & Messages

1

-

87

RAP 1-34

Error Code C9-2

Paper Jam

Reset
ENV/Bypass

There is a paper jam between the Multi-sheet Bypass Feeder and Tray 2 Take Away

Sensor.

Logic Control on the Print Engine Controller Board sensed that when paper was fed

from the Multi-sheet Bypass Feeder, Tray 2 Take Away Sensor did not actuate within

the specified time after the Multi-sheet Bypass Feeder Feed Clutch was actuated.

Table 1-62 Error Code C9-2 Paper Jam Reset ENV/Bypass

Step

Actions and Questions

Yes

No

1

PAPER INSPECTION

Inspect the paper that is loaded in the Multi-sheet Bypass
Feeder.

Is the paper loaded in the Multi-sheet Bypass
Feeder wrinkled or damaged?

Replace the
paper with
new paper

Go to step 2

2

PAPER PATH INSPECTION

Inspect the paper path for paper scraps or foreign objects
that could cause a paper jam.

Is the paper path clear?

Go to step 3

Clear the
paper path

3

MULTI-SHEET BYPASS FEEDER FEED
ROLLER INSPECTION

1. Run a Test Print, feeding from the Multi-sheet Bypass

Feeder.

2. Observe the paper in the Multi-sheet Bypass Feeder

Bin.

Is the paper partially fed out of the Multi-sheet
Bypass Feeder Bin?

Replace the
Multi-sheet
Bypass
Feeder Feed
Roller (RRP
1-30), Pick
Roller (RRP
1-31), and
Multi-sheet
Bypass
Feeder Pad
(RRP 1-33)

Go to step 4

4

MULTI-SHEET BYPASS FEEDER DRIVE TEST

Remove the Rear Cover (RRP 1-5) so you can observe
the Main Drive Assembly and the Multi-sheet Bypass
Feeder Multi-sheet Bypass Feeder Drive Gear
Assembly.
1. Place a sheet of paper in the Multi-sheet Bypass

Feeder.

2. Enter Diagnostics Mode.
3. From the Main Menu, select Comp Output Test /

MBF/ENV Unit / MBF Feed Clutch to check the
Multi-sheet Bypass Feeder Drive Assembly.

4. Press [4] to start, clutch should actuate for two

seconds, then release.

5. Rotate the Main Drive Motor counter clockwise and

observe the paper in the MBF.

Does the paper begin to feed into the paper
path, indicating the Main Drive Assembly
rotated the Multi-sheet Bypass Feeder Drive
Gear Assembly?

Go to step 5

Replace the
Multi-sheet
Bypass
Feeder
Assembly
(RRP 1-25)

«
...
107
108
109
110
111
...
»

Содержание DocuPrint N4525





























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды