Xerox DocuPrint N4525 Скачать руководство пользователя страница 103

Страница: 103 / 380

Volume 1 / Print Engine - Error Codes & Messages

RAP 1-30

Error Code C1-3

Clear Area A

Reset Tray 1

There is a paper jam between Paper Tray 1 and the Registration Sensor.

Logic Control on the Print Engine Controller Board sensed that the Registration

Sensor did not actuate within the specified time after the Tray 1 Feed Clutch was

actuated.

Table 1-58 Error Code C1-3 Clear Area A Reset Tray 1

Step

Actions and Questions

Yes

PAPER INSPECTION

Inspect the paper that is loaded in the paper tray.

Is the paper loaded in the cassette wrinkled or
damaged?

Replace the
paper with
new paper

Go to step 2

PAPER PATH INSPECTION

Inspect the paper path for paper scraps or foreign objects
that could cause a paper jam.

Is the paper path clear?

Go to step 3

Clear the
paper path

Tray 1 LIFT MOTOR TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Output Test / IOT

Unit / Tray 1 Lift Mot to test the Tray 1 Lift Motor
function.

3. Press [4] to start, the Tray 1 Lift Motor should actuate

for two seconds, then stop.

Does the Motor switch on when you start the
Output Test?

Go to step 4

Replace Tray
1 Lift Motor
(RRP 1-9)

Tray 1 FEED CLUTCH TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Output Test / IOT

Unit / Tray 1 Feed Clut to check the Tray 1 Feed Clutch
function.

3. Press [4] to start, the clutch should actuate for two

seconds, then release.

Does the Tray 1 Feed Clutch actuate when you
start the Output Test?

Go to step 5

Replace the
Tray 1 Feed
Clutch (RRP
1-10)

REGISTRATION SENSOR TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Input Test / IOT

Unit / Reg. Sensor.

3. Press [4] to start, [0] to stop.
4. Insert, then remove, a sheet of paper into the

Registration Sensor.

Does the Control Panel display “with paper”
when you insert the paper into the Registration
Sensor, and is “without paper” displayed when
you remove the paper?

Go to step 6

Replace the
Registration
Sensor

PRINT ENGINE CONTROLLER BOARD
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 7

Problem
solved

Содержание DocuPrint N4525





























































































































































































































































































































































































Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды

Xerox DocuPrint N4525, Справочное руководство по обслуживанию

Результаты поиска

Содержание DocuPrint N4525

Отзывы:

Бренды по названию

Популярные бренды