Xerox DocuPrint C3055 Скачать руководство пользователя страница 222

Страница: 222 / 239

222

A Appendix

Unlock the castor stoppers. Hold the printer as in the figure and push it underneath
the scanner stand.

Important

• When moving the printer, be careful not to step on its power cord.

After moving the printer, lock the castor stoppers.

Plug the other end of the USB cable connected to the scanner into the USB connector
located on the rear side of the printer.

When Replacing Consumable or Installing Optional Accessories

Follow these precautions when replacing a consumable or installing an optional accessory.

• When replacing a consumable, release the lock on the castor base or cabinet, and pull

the printer at least 200 mm away from the scanner stand.

• When installing an optional accessory to the printer, pull the printer at least 200 away from

the scanner stand. Then, rotate the printer 90 degrees, and open the rear cover to install
the accessory.

• The front wheels of the cabinet or castor base have stoppers that prevent the cabinet or

castor base from moving. Make sure to lock the stoppers after moving the printer to the
desired location. If you leave the stoppers unlocked, the printer may move unexpectedly
and cause injuries.

• Make sure to leave the power on when removing consumables or clearing paper jams.

When moving the printer, be careful not to step on its power cord.

When pulling the printer, use the handle on the
cabinet or castor base.

When pushing the printer underneath the
scanner stand, hold the printer by these areas.

Lock

Unlock

Содержание DocuPrint C3055















































































































































































































































Результаты поиска

Содержание DocuPrint C3055

Отзывы:

Похожие инструкции для DocuPrint C3055

Бренды по названию

Популярные бренды

Xerox DocuPrint C3055, Руководство пользователя

Результаты поиска

Содержание DocuPrint C3055

Отзывы:

Похожие инструкции для DocuPrint C3055

Бренды по названию

Популярные бренды