PAPER FACTS
Table 3-5.
Paper stocks guide (continued)
Stock type
Instructions for use
3-hole drilled, edge
reinforced
dual-purpose
•
Use trays 1 and 2.
•
Load paper with holes to the right, reinforced side DOWN.
•
In two-sided (duplex) printing, degraded print quality may occur near the
reinforcement.
•
Leave stock in wrapper until use to achieve maximum stock flatness.
•
Run with no more than 200 sheets in a tray.*
Transparencies—
Oversized (8.5 by 14
inches, 0.5 inch
white stripe/
216 by 356 mm, 1 mm
white strip)
•
Load with the white stripe to the RIGHT in trays 1 and 2 (“shiny” side UP for
best performance).
•
Simplex only
Preprinted stock
Certain types of ink or insufficient drying time may cause the ink to adhere to
various machine components and printed sheets. Allow at least 3 hours of
drying time before using preprinted stock.
CAUTION: Certain preprinted stocks lie unevenly in the feeder trays. If the right
side of the stack is higher than the left in trays 3, 4, 5 and 6 SEVERE hardware
damage can occur. Load the stock in trays 1 or 2 or load fewer sheets.
Transparencies—
Paper-backed,
high-speed,
removable stripe
•
High-speed paper-backed transparencies may be run from trays 1 and 2 with
paper side DOWN.
•
Run no more than 50 removable stripe transparencies at one time.
•
Load the transparencies on top of approximately 50 sheets of paper.
Tab stock
•
Load into trays 1 and 2 with tabs to the LEFT.
•
For best performance, print should be centered on the tab and should not
extend to either edge.
•
Use tab stock in perfectly flat condition. DO NOT use deformed, bent, or
damaged tabs.
9-inch cover stock
110 pound/200 gsm
Load into any tray.
High-speed label stock
•
Load FACE UP.
•
DO NOT run two-sided (duplex) prints.
Letterhead
•
Load into trays with side 1 UP and top edge toward the front of the tray
(avoid placing the print in line with the feed belt in trays 1 and 2).
•
Avoid using freshly preprinted paper.
Manual two-sided
(duplex) prints
•
Load into trays with printed side DOWN and top edge toward the front of
the tray (avoid placing the print in line with the feed belt in trays 1 and 2).
•
Print the second side as soon as possible after the first side to prevent
wrinkling and excessive curl.
Textured paper
•
Heavily textured paper may yield prints with ragged character appearance
and/or deletions. To test, print a sample sheet.
* You can order a mylar reinforcement tray which allows a
feeder tray to handle up to 500 sheets of this type of stock.
Contact your service representative for additional information.
XEROX 4635 LASER PRINTING SYSTEM OPERATOR GUIDE
3-7
Содержание DocuPrint 4635
