Xerox B205 Скачать руководство пользователя страница 42

Страница: 42 / 206

July 2019

2-21

Xerox® B205/B215 Multifunction Printer Service Manual

15-100, 15-110, 15-130, 15-340

Status Indicator RAPs

Initial Release

15-100, 15-110 Scan to E-mail RAP

Control Panel Fault Displayed

15-100

No Email address assigned to group name.

B205: Group Not Available

B215: No Email Address for Group Name

15-110

Email SMTP server returned an error during transmission.

B205: Email Send Error

B215: Email Send Error

Faults displayed when the device encounters scan to e-mail problems. The faults are listed in
code order, together with any recommended action. Please note that service actions are lim-
ited.

Procedure

15-100 Group Name has no Assigned Email Address

No email address is assigned to the group name.

•

Remove the group name from the ‘To:’ field or enter a valid email address.

15-110 Email Send Failed

The email SMTP server returned an error during transmission. The SMTP server authentica-
tion may be supported but not enabled on the device.

•

Verify SMTP authentication is enabled on the machine.

•

Resend the email.

15-130, 15-340 Mail Too Large RAP

Control Panel Fault Displayed

15-130

This error is raised when the MFP is unable to split the mail and send it.

B205: NA

B215: Mail Size Limit has been Exceeded

15-340

Maximum mail size configured exceeds the server limit.

B205: Mail Exceeds Server Support

B215: Maximum Mail Size has been Exceeded

The mail size has exceeded the server support.

Initial Actions

•

Reduce max mail size option.

•

Increase mail size on this device via CentreWare Internet Services

Procedure

If problem persists, increase mail size allotment on mail server.

Содержание B205














































































































































































































Результаты поиска

Содержание B205

Отзывы:

Похожие инструкции для B205

Бренды по названию

Популярные бренды

Xerox B205, Руководство по обслуживанию

Результаты поиска

Содержание B205

Отзывы:

Похожие инструкции для B205

Бренды по названию

Популярные бренды