Xerox B205 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 206

background image

July 2019

1-3

Xerox® B205/B215 Multifunction Printer Service Manual

Service Call Overview, Safety Precautions

Service Call Procedures

Initial Release

Service Call Overview

This section provides an overview of actions a service technician should take when servicing a
machine. Refer to the checklist below as a guide for steps to take when troubleshooting prob-
lems with the printer. Follow all precautions listed in the Safety Precautions section.

1.

Identify the problem

•

Verify that the problem exists.

•

Record any error codes.

•

Print both customer and test prints.

•

Make note of any image quality problems in the test prints.

•

Observe if any unusual odors or noises coming from the printer.

•

Ensure that the AC input power is within specifications.

•

From the Diagnostics Mode, print an Error Information Report.

2.

Inspect and clean the printer

•

Disconnect and inspect the power cord.

•

Inspect the interior of the printer. Remove any debris or contamination.

•

Inspect the printer for damaged wires, loose connections toner leakage or any other
worn or damaged parts.

3.

Find the cause of the problem.

•

Use troubleshooting procedures to find the root cause of the problem

•

Use diagnostics to check the printer and components

•

Use the BSDs to locate test points.

•

Take voltage readings as instructed in the troubleshooting procedure.

4.

Correct the problem

•

Use the Parts List to locate part numbers.

•

Use the Repair Procedures to replace parts.

5.

Final Actions

•

Test the printer to verify that the problem has been corrected and that there are no
additional problems.

Diagnostic Mode

The Xerox® B215/B205 has built-in diagnostics to test components, display status and some
NVM access. The diagnostic tests are accessed through the Control Panel. Refer to the User
Guide for detailed instructions on using the Control Panel buttons and menus. Refer to Section
6 for diagnostic test menus.

Safety Precautions

Ensure that all Cautions and Warnings detailed in the service procedures are followed when
servicing the machine.

Failure to follow the following instructions could cause an electrical shock or fire hazard.

•

Only use the Power Cord supplied with this product.

Do not allow the Power Cord to become twisted, bent, or damaged.

•

Do not allow liquids to spill on or into the machine.

•

Do not allow paper clips, pins or other objects to fall into the machine.

•

When replacing the SMPS PWB wait 5 minutes after unplugging the Power Cord before
removing the PWB. This allows the PWB to discharge, preventing electrical shock.

Laser Safety

•

The Laser system is designed so there is never human access to the Laser radiation dur-
ing normal operation, user maintenance, or service maintenance.

•

Do not bypass or disable any laser safety devices or attempt to service the Laser.

«
...
16
17
18
19
20
...
»

Содержание B205















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B205

Бренд: EASYPRINT Страницы: 37

Бренд: IBM Страницы: 334

Бренд: IBM Страницы: 428

Бренд: IBM Страницы: 316

Бренд: IBM Страницы: 210

Бренд: Xerox Страницы: 16

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 2

WORKCENTRE 5050

Бренд: Xerox Страницы: 186

Бренд: Tally Страницы: 28

Бренд: Partner Страницы: 15

Бренд: Parkside Страницы: 176

275C - SRP Two-color Dot-matrix Printer

Бренд: BIXOLON Страницы: 100

Бренд: A&D Страницы: 66

Бренд: Oki Страницы: 45

Бренд: Kyocera Страницы: 24

ThermalTronix TT-1025EX-MIL

Бренд: Intellisystem Страницы: 11

Бренд: TransAct Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды