Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 202 | Manualshive

Страница: 202 / 503

Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 202

Phaser 5400 Laser Printer Service Guide

173

RAP 69 Erratic Printer Operation

The printer has a variety of problems that are not identified by displayed error codes

or messages. Problems may range from incomplete or garbled display text to
intermittent power shutdowns.

Table 99

Erratic Printer Operation Troubleshooting Procedure

Step Actions and Questions

Yes

No

1

PRINTER OPERATING ENVIRONMENT CHECK

Compare the printer room environment, such as
temperature, humidity, and space requirements, with
the specifications listed in General Information section
of this manual.

Does the printer room environment meet printer

specifications as listed in the General

Information Section?

Go to
Step 2.

Move the
printer to an
environment
that meets
printer
specs.

2

AC POWER CHECK

1. Unplug the printer AC power cord from the AC wall

outlet.

2. Use a digital multimeter to monitor the voltage at the

AC wall outlet.

3. Monitor the AC voltage for 30 minutes or longer.

Does the voltage at the AC wall outlet meet

printer specifications as listed in the General

Information Section and does the voltage remain

relatively stable without wide fluctuations?

Go to
Step 3.

Have an
electrician
troubleshoot
the AC line.

3

AC POWER CORD REPLACEMENT

1. Replace the AC Power Cord.

2. Monitor printer operation.

Does the printer display erratic operation?

Go to
Step 4.

Problem
solved.

4

TEST PRINTS

1. Enter Diagnostics mode.

2. From the Main Menu, select Test Print / Print Pattern /

press [4] to start printing, [0] to stop.

3. Run 20 test prints.

Does the printer generate test prints?

Go to
Step 6.

Go to
Step 5.

5

LVPS +5 VDC CHECK

1. Switch printer power OFF.

2. Disconnect P/J168 from the LVPS Assembly.

3. Switch printer power ON.

4. Measure the voltage between P161-10 and frame

ground.

Does the voltage between P161-10 and frame

ground m5.0 VDC?

Go to
Step 6.

Go to
Step 11.

«
...
200
201
202
203
204
...
»

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды