manualshive.com logo in svg

Xerox 5400N - Phaser B/W Laser Printer, Справочное руководство по обслуживанию

Поделиться
Скачать
Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 190

Phaser 5400 Laser Printer Service Guide 

161

RAP 62 500-Sheet Feeder Feed Solenoid

The 500-Sheet Feeder is not feeding paper or not feeding paper at the correct time.

Table 92

500-Sheet Feeder Feed Solenoid 

Troubleshooting Procedure

Step Actions and Questions

Yes

No

1

PROCEDURE

1. Enter Diagnostics mode.

2. From the Main Menu, select Component Test / Tray 2 

Feed Sol (or Tray 3 Feed Sol) / press [4] to start.

Can you hear the solenoid energize?

Go to 
Step 10.

Go to 
Step 2.

2

“NO” FROM STEP 2 ABOVE

1. Switch printer power OFF.

2. Remove the 500-Sheet Feeder Left Cover [RRP 11.3, 

page 330

].

3. Disconnect P/J133 on the Feeder Board.

4. Measure the resistance between pins 10 and 11 on 

the disconnected plug.

Does the resistance measure approximately 

90 ohms?

Go to 
Step 4.

Go to 
Step 3.

3

“NO” FROM STEP 2 ABOVE

1. Disconnect P/J135 from the Feed Head Assembly.

2. Measure the resistance between P135-1 and P135-2.

Does the resistance measure approximately 

90 ohms?

Repair or 
replace the 
Feed Head 
Harness 
[PL 11.3, 

page 416

].

Replace the 
Tray 2/3 
Feed 
Solenoid 
[RRP11.10, 

page 337

].

4

“YES” FROM STEP 2 ABOVE

1. Switch printer power ON.

2. Measure the voltage between P/J133-10 on the 

Feeder Board and frame ground.

Does the voltage m24 VDC?

Go to 
Step 7.

Go to 
Step 5.

5

“NO” FROM STEP 4 ABOVE

Measure the voltage between P/J132-3 and frame 
ground.

Does the voltage m24 VDC.

Replace the 
Feeder 
Board 
[RRP 11-7, 

page 334

].

Go to 
Step 6.

6

“NO” FROM STEP 5 ABOVE

1. Switch printer power OFF.

2. Remove the print Left Side Cover [RRP 1.1, 

page 250

] and the Print Engine Controller Board 

Cover [RRP 8.5, 

page 310

].

3. Switch printer power ON.

4. Measure the voltage between P/J13-3 and frame 

ground.

Does the voltage m24 VDC?

Check the 
continuity of 
the Feeder 
Harnesses 
[P/J132 to 
P/J131 and 
P/J131 to 
P/J13]. 
Repair or 
replace as 
necessary.

Replace the 
Print Engine 
Controller 
Board 
[RRP 8.5, 

page 310

].

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды