Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 188

Страница: 188 / 503

Phaser 5400 Laser Printer Service Guide

159

RAP 61 Low Paper Tray 2 (or Tray 3) /

500-Sheet Feeder

Tray 2 and/or Tray 3 have low paper.

Table 91

Low Paper Tray 2 (or Tray 3) / 500-Sheet Feeder Troubleshooting

Procedure

Step Actions and Questions

Yes

PROCEDURE

Fill the affected paper tray with fresh paper.

Is the error code still displayed?

Go to
Step 2.

Problem
solved.

LOW PAPER SENSOR ACTUATOR TEST

1. Remove the paper tray from the 500-Sheet Feeder

Assembly.

2. Manually push up and release the low paper actuator.

Does the low paper sensor actuator move

smoothly up and down?

Go to
Step 3.

Replace the
Low Paper
Sensor
Actuator
[RRP 11.18,

page 347

] or

the Tray 2/3
Left Guide
Assembly
[RRP 11.13,

page 340

LOW PAPER SENSOR ACTUATOR

1. Enter Diagnostics mode.

2. From the Main Menu, select Component Test / Sensor

Input / press [4] to start, [0] to stop.

3. Press and release the Low Paper Sensor Actuator.

Does the LCD counter increment each time you

press and release the actuator?

Replace the
Print Engine
Controller
Board
[RRP 8.5,

page 310

Go to
Step 4.

FEEDER BOARD

1. Switch printer power OFF.

2. Remove the 500-Sheet Feeder Left Cover [RRP 11.3,

page 330

3. Disconnect P/J133 from the Feeder Board.

4. Switch printer power ON.

5. Measure the voltage between P133-1 and frame

ground, then measure the voltage between P133-3

and frame ground.

Are both measur3.3 VDC?

Go to
Step 5.

Replace the
Feeder
Board
[RRP 11-7,

page 334

“YES” FROM STEP 4 ABOVE

1. Switch printer power OFF.

2. Reconnect P/J133.

3. Switch printer power ON.

4. Measure the voltage between P/J133-3 and frame

ground as you actuate and deactuate the Low Paper

Sensor.

Does the voltage m0.0 VDC when

deactuated and +3.2 VDC when actuated?

Go to
Step 7.

Go to
Step 6.

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Результаты поиска

Содержание 5400N - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Xerox 5400N - Phaser B/W Laser Printer, Справочное руководство по обслуживанию

Результаты поиска

Содержание 5400N - Phaser B/W Laser Printer

Отзывы:

Бренды по названию

Популярные бренды