Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 503

Xerox 5400N - Phaser B/W Laser Printer Скачать руководство пользователя страница 139

110

Phaser 5400 Laser Printer Service Guide

Printer Performance Problems

RAP 38 AC Power

There is a possible problem with the AC power.

Initial Action

Disconnect the AC power cord from the wall outlet.

Warning: Improper connection of the grounding conductor can

result in the risk of electrical shock. The following must be

observed:

■

Never use a ground adapter plug to connect the machine to a
power source.

■

Never attempt any maintenance function which is not specifically
called out in the service procedures.

■

Never remove any covers which are fastened with screws, unless so
instructed in the service procedures.

Caution: If any of the voltage measurements are not as specified in

the following steps, the cause must be corrected. Caution
the customer NOT to connect the machine to the wall

outlet. Advise the customer that a licensed electrician must
correct the wiring. Do not attempt to correct the wiring
yourself. If you later find the condition has not been

corrected, inform your manager in writing of the improper
wiring.

Table 62

AC Power Testing Procedure

Step Actions and Questions

Yes

No

1

US, XCI and AO [110 VAC]

1. Measure the AC voltage between AC Line and

Neutral, between AC Line and Ground, and between

AC Neutral and Ground.

2. The voltage between Line and Neutral and between

Line and Ground should range from 104 to 127 VAC

and the voltage between Neutral and Ground should

be less than 3 VAC.

Is the AC voltage within specification?

Go to
Step 4.

Inform
customer of
insufficient
voltage or
improper
wiring.

«
...
137
138
139
140
141
...
»

Содержание 5400N - Phaser B/W Laser Printer
























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды