Xantrex PROwatt 3000 Скачать руководство пользователя

Страница: 74 / 82

Product and System Information

D–4

Information About Your System

As soon as you open your PROwatt 3000 package, record the following
information and be sure to keep your proof of purchase.

If you need to contact Customer Service, please record the following
details before calling. This information will help our representatives give
you better service.

❐

Serial Number (on DC
end)

______________________________

❐

Purchased From

______________________________

❐

Purchase Date

______________________________

❐

Type of installation (e.g.
RV, boat, home)

______________________________

❐

Length of time inverter
has been installed

______________________________

❐

Battery/battery bank size

______________________________

❐

Battery type (e.g.
flooded, sealed gel cell,
AGM)

______________________________

❐

DC wiring size and
length

______________________________

❐

Alarm sounding?

______________________________

❐

Description of indicators
on front panel

______________________________

❐

Appliances operating
when problem occurred

______________________________

❐

Description of problem

______________________________

_____________________________________________________

Содержание PROwatt 3000



















































































Результаты поиска

Содержание PROwatt 3000

Отзывы:

Похожие инструкции для PROwatt 3000

Бренды по названию

Популярные бренды

Xantrex PROwatt 3000, Руководство пользователя

Результаты поиска

Содержание PROwatt 3000

Отзывы:

Похожие инструкции для PROwatt 3000

Бренды по названию

Популярные бренды