Xantrex PROwatt 3000 Скачать руководство пользователя

Страница: 20 / 82

PROwatt 3000 Features

2–4

Front Panel With AC Receptacle

Figure 2-1 Front Panel With AC Receptacle

①

②

③

④

⑤

}

⑦

⑧

⑨

⑩

Feature Description

➀

On/Off Switch

This switch turns the inverter’s control circuit on and

off. It is not a power disconnect switch. You must disconnect AC and
DC power before working on any circuits connected to the inverter.

➁

OVER TEMP

Indicator

This indicator lights when the inverter shuts

down to protect itself from overheating. When the inverter cools, it
restarts automatically, and the indicator turns off.

➂

OVER LOAD

Indicator

This indicator lights when the inverter shuts

down because of an AC overload or a short circuit.

➃

VOLTS

and

AMPS

Indicators

These display battery voltage and

current. (See

“Reading the Front Panel Indicators” on page 4–3

for

details.)

Содержание PROwatt 3000



















































































Результаты поиска

Содержание PROwatt 3000

Отзывы:

Похожие инструкции для PROwatt 3000

Бренды по названию

Популярные бренды

Xantrex PROwatt 3000, Руководство пользователя

Результаты поиска

Содержание PROwatt 3000

Отзывы:

Похожие инструкции для PROwatt 3000

Бренды по названию

Популярные бренды