Xantrex 815-3012-02 Скачать руководство пользователя | Manualshive

Страница: 8 / 76

background image

Precautions When Preparing to Charge

8

Freedom SW-RVC Installation Guide

NOTES

:

1. Mount and place the Freedom SW-RVC Inverter/Charger unit

away from batteries in a well ventilated compartment.

2. Always have someone within range of your voice or close

enough to come to your aid when you work near a lead-acid
battery.

3. Always have plenty of fresh water and soap nearby in case

battery acid contacts skin, clothing, or eyes.

4. Keep battery terminals clean from corrosion. If battery acid or

corrosion deposit contacts skin or clothing, wash immediately
with soap and water. If battery acid or corrosion deposit enters
your eye, immediately flood it with running cold water for at
least twenty minutes and have someone within range of your
voice or close enough to get medical attention immediately.

5. Use extra caution to reduce the risk of dropping a metal tool on

the battery. It could spark or short circuit the battery or other
electrical parts and could cause an explosion. Use tools with
insulated handles only.

6. Batteries can produce a short circuit current high enough to

weld a ring or metal bracelet or the like to the battery terminal,
causing a severe burn.

7. When removing a battery, always remove the negative

terminal from the battery first for systems with grounded
negative. If it is grounded positive, remove the positive terminal
first. Make sure all loads connected to the battery and all
accessories are off so you don’t cause an arc.

Precautions When Preparing to
Charge

WARNING

EXPOSURE TO CHEMICALS AND GASES HAZARD

• Make sure the area around the battery is well ventilated.
• Make sure the voltage of the batteries matches the output voltage of the

inverter/charger.

• Be careful to keep corrosion from coming into contact with your eyes and skin

when cleaning battery terminals.

Failure to follow these instructions can result in death or serious
injury

.

NOTES

:

n

Study and follow all of the battery manufacturer's specific
precautions, such as removing or not removing cell caps while
charging, whether equalization is acceptable for your battery,
and recommended rates of charge.

n

For flooded non-sealed batteries, add distilled water in each
cell until battery acid reaches the level specified by the battery
manufacturer. This helps to purge excessive gas from cells. Do
not overfill. For a battery without removable cell caps, carefully
follow manufacturer's instructions.

«
...
6
7
8
9
10
...
»

Содержание 815-3012-02













































































Отзывы:

Нет отзывов

Похожие инструкции для 815-3012-02

Бренд: Sima Страницы: 2

MONO MIXER SERIES

Бренд: Audioplex Страницы: 1

Бренд: Velleman Страницы: 48

Бренд: Somogyi Elektronic Страницы: 10

Бренд: CYP Страницы: 60

Бренд: Goodwe Страницы: 50

Бренд: T-TeleSec Страницы: 21

Бренд: Patton electronics Страницы: 11

Parallel Port Input/Output Converter PPIO

Бренд: B&B Electronics Страницы: 34

Бренд: KanexPro Страницы: 32

Бренд: FOLSOM Страницы: 61

Бренд: Vacon Страницы: 12

TopTronic E Solar TTE-SOL

Бренд: Hoval Страницы: 95

Rossini Transport

Бренд: DCS Страницы: 31

Бренд: National Communications Страницы: 20

CSAD UiAWP 100 PS Series

Бренд: d2itsu Страницы: 56

Бренд: R&S Страницы: 401

Бренд: ALM Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды