background image

1

Modules & Connecting Blocks

INSTALLATION INSTRUCTIONS

CB60

CONNECTING BLOCK

The Model CB60 provides a means for quick connection of certain
Xantech IR Receivers, such as the 490-30, to up to six emitters and
a power supply.  It can also provide a low cost means of easy emitter
expansion for existing systems or to connect multiple emitters at the
output of other Xantech devices, such as the 590 Programmable
Controller, the 710 Fone Link, 792-10 Power Module and certain
connecting blocks, such as the CB12 and the 791-44.

SPECIFICATIONS

• IR Receiver Input: 3.5mm stereo mini phone jack.

• Outputs: 6 emitter ports (3.5mm mono mini type phone jacks) in a parallel hook-up.

• Contains a 100 Ohm resistor in series with each emitter output.

• 282, 283, 284, 284-10, and 286 mini-emitters may be used.

• Power requirements: 12 volts DC. Uses 781RG or 782  Power Supplies.  

Note:

 A power supply 

is not

used when the CB60 is used solely as an emitter expander.

• 2.1 mm coaxial power jack.

• Dimensions: 2-15/16" W  x 1-3/4" D x 13/16" H

INSTALLATION

The following diagram, 

Fig. 2

, illustrates the primary use of the CB60; to connect a Xantech IR Receiver,

equipped with a 3.5 mm stereo mini plug, into an IR controlled system.  In this case a 490-30 is shown
plugged into the "IR Receiver" jack on the CB60.

Note that everything is quick connect; the IR receiver, the power supply and the emitters.  (Since the emitter
ports are connected in parallel within the CB60, you may plug in the 283M's in any order).  The 490-30 &
CB60 are intended for use in installations where the connecting block is within reach of the 7-foot cable on
the 490-30 -- such as when installing the 490-30 in a cabinet where the controlled equipment is behind
closed doors.

The Mini-Emitters, any of the 282, 284, 283 &
286 series, may be affixed directly over the
infrared window of the controlled device, us-
ing the clear adhesive layer on the flat surface
of the emitter.  In some applications, it may be
desirable to affix the flat surface of the 282M
higher output emitters to a cabinet door, side
or shelf with the rounded surface aimed at the
infrared window.  Maximum output from the
282M comes from the rounded surface oppo-
site the adhesive layer.

Fig. 1

 Model CB60 Connecting Block

1         2         3

EMITTERS

POWER

12VDC

RECEIVER

I R

4         5         6

EMITTERS

CB60

CONNECTING BLOCK

®

Fig. 2

  A Typical CB60/490-30 IR System

VCR

To 120 V AC
(Unswitched)

781RG

Power Supply

CB60

Connecting Block

283M

 

Blink IR™

Controlled Equipment
(mounted behind
closed cabinet doors)

Cassette DecK

283M

 

Blink IR™

283M

 

Blink IR™

283M

 

Blink IR™

283M

 

Blink IR™

Mouse Emitter

7 Foot
3-Conductor
Cable with
Quick Connect
 Mini Plug

490-30

Series

Micro Link

IR Receivers

(mounted on

or near

cabinet in an

inconspicuous

location).

Hand Held

Remote

1    2    3

EMITTERS

POWER

12VDC

RECEIVER

IR

4    5    6

EMITTERS

SYLMAR,

C

A

®

CB60

CONNECTING BLOCK

AV 

Receiver

CD Changer

Satellite Receiver

Отзывы: