background image

 

 

 

08905099B 

 

  - 

INSTALLATION INSTRUCTIONS 

 

480-95 

Plasma Friendly Dinky Link IR Receiver 

 

DESCRIPTION 

The 480-95 is a Plasma Friendly version of the 480-00 series Dinky Link IR receivers. It is specifically 
designed to have greater immunity to plasma infrared inference and to have exceptional IR reception 
range. Besides showing great immunity to plasma emissions, the 480-95 (as well as all Xantech 
Plasma-Friendly Receivers) work well in the presence of Sunlight and Fluorescent lighting. Their 

wide-bandwidth

 reception allows them to be used with a much wider assortment of IR Controllable 

products that the competition assuring the ‘job will get done’ the first time around without un-wanted 
service calls.   
 
These small IR receivers have been designed for mounting in very small spaces. They may be 
mounted under shelf edges, cabinet ledges, in-wall speakers, etc. anywhere an inconspicuous 
appearance is desired. The high sensitivity of these receivers allows placement behind speaker 
grilles and still receive IR commands up to 20 feet away. If longer range is necessary, a 3/8-inch hole 
must be drilled in the grilled to allow unobstructed entry of the IR signal.  
 

FEATURES 

ƒ

  Black, silver, and white color available. 

ƒ

  Works in normal 3-wire mode (12VDC, IR, GND). 

ƒ

  Red talkback LED for system verification. 

ƒ

  Improved Fluorescent light rejection (under most conditions) and rejection from LCD 

Displays. 

ƒ

  Includes 3-Terminal Block for easy extension of 7 foot ribbon cable. 

ƒ

  7 units may be powered by one 781RG power supply.  

ƒ

  Normal Operating Power: +12VDC, 20mA. 

Note

: The 480-95 will not operate in 2-wire Phantom Power mode.  

Содержание 480-95












Отзывы: