XAG P100 Pro Скачать руководство пользователя страница 169

Страница: 169 / 184

169

XAG AUSTRALIA

Maintenance Cycle – Propulsion

Component

Service Schedule

(Recommended)

Service Plan

(Recommended)

Motor

Daily

01.

Ensure the Motors are clean using compressed air.

02.

Manually rotate the Motor to ensure smooth
operation without any abnormal sounds.

03.

Ensure the Motor enamelled wire is free from
damage or fractures.

04.

Ensure the Motor and Motor Bracket are securely
fastened.

05.

Ensure the connectors between the Motor and the
ESC are securely fastened and show no signs of
melting or damage.

Motor Connector Isolator

(Thick & Thin)

Daily

Ensure the Isolators (Thin & Thick) are intact, retaining
their original colour, and show no signs of heat-induced
discoloration or wear.

Motor Connector

Bracket

Daily

Ensure the Connector Brackets are intact, clean, and free
from any signs of corrosion or wear.

Propeller

Daily

01.

Ensure the Propeller is free from damage, cracks,
softening, or deformation.

02.

Ensure the Propellers are correctly installed with no
missing or loose screws between the Propeller and
Propeller Clamp.

03.

Clean the Propeller using a wrung-out wet rag to
remove any stains or foreign objects.

Propeller Clamp

Daily

01.

Ensure the Clamp is free from damage, cracks, or
deformation.

02.

Ensure the Clamps are correctly installed with no
missing or loose screws.

Propeller Clamp

Bracket

Daily

01.

Ensure the Bracket is free from damage, cracks, or
deformation.

02.

Ensure the Brackets are correctly installed with no
missing or loose screws between the Clamp and
Clamp Bracket.

Propeller Clamp Pin

Weekly

Ensure the Clamp Pins are free from damage, cracks, or
deformation and are securely in place.

Propeller Gasket

(CW / CCW)

Weekly

Ensure the Gaskets are in good condition and not
excessively worn. Test by swaying the propeller blade tip to
check for any wobbling.

Clamp Bracket Pin

Bushing

Monthly

Ensure the Pin Bushings are in good condition and not
excessively worn or damaged.

Содержание P100 Pro

























































































































































































Результаты поиска

Содержание P100 Pro

Отзывы:

Бренды по названию

Популярные бренды

XAG P100 Pro, Руководство по эксплуатации для пилотов

Результаты поиска

Содержание P100 Pro

Отзывы:

Бренды по названию

Популярные бренды