manualshive.com logo in svg

XAG P100 Pro, Руководство по эксплуатации для пилотов

Поделиться
Скачать
XAG P100 Pro Скачать руководство пользователя страница 153

153

XAG AUSTRALIA

06.  Take-off: Initiate manual take off by moving both sticks to the inner-lower corners or outer-lower 

corners simultaneously. This action should be performed smoothly and quickly. Once you've 
completed the CSC, you'll have 3 seconds to push the throttle stick upwards to lift the drone off 
the ground. If you don't do this within the 3 seconds, the motors will automatically shut down.

07.  Setting First Boundary (A): Navigate the drone to the initial boundary point of the field (A). Adjust 

the drone's heading by yawing left or right to select your boundary direction. Short press the L1 
Button to set the first Boundary (A).  
 
 

Manual Take-off and Setting Boundaries

Ⓝ

 

Notes

Monitor the added points by checking the     ,     ,     at the bottom of each icon. Tap "Undo" 

if you need to modify the boundary point or its direction.

Содержание P100 Pro

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды