XAG P100 Pro Скачать руководство пользователя

Страница: 103 / 184

103

XAG AUSTRALIA

Turning On the Aircraft:

01. Initiate by inserting the battery into the aircraft's battery compartment. Again, gently push

downward until a clicking sound is heard, indicating that the battery terminal is now connected
to the aircraft.

02. Proceed by pressing and holding the power button on the battery for about 1 second. Upon

doing this, all indicator lights should flash. Press and hold the power button once more for
around 1 second until a beep from the battery is heard.

03. After completing these steps, kindly wait until the Aircraft Flight Status (ESC) Indicator flashes

green three times. This sequence of flashes signals that the aircraft is now ready for use.

Turning Off the Aircraft:

01. Begin by pressing and holding the power button on the battery once for approximately 1 second

until all the indicator lights flash. Following this, press and hold the power button once more for
about 1 second until a beep from the battery is heard.

02. At this point, both the Battery Indicator and Aircraft Flight Status (ESC) Indicator will switch off,

signalling that the battery can now be safely removed or replaced as necessary.

Turning the Aircraft ON/OFF

Содержание P100 Pro

























































































































































































Результаты поиска

Содержание P100 Pro

Отзывы:

Похожие инструкции для P100 Pro

Бренды по названию

Популярные бренды

XAG P100 Pro, Руководство по эксплуатации для пилотов

Результаты поиска

Содержание P100 Pro

Отзывы:

Похожие инструкции для P100 Pro

Бренды по названию

Популярные бренды