manualshive.com logo in svg

XAG P100 Pro, Руководство по эксплуатации для пилотов

Поделиться
Скачать
XAG P100 Pro Скачать руководство пользователя страница 102

XAG AUSTRALIA

102

Install the Battery

To install the battery, insert it into the aircraft's battery compartment. Apply a gentle downward force 
until you hear a clicking sound. This audible click confirms that the battery terminal has made a 
successful connection with the aircraft.

 

ℹ

Prior to the battery installation, it is imperative to ensure the power connector of the aircraft 
and the battery connector are clean, dry, and devoid of any metal foreign objects or liquids. 
This preventive measure is critical to maintaining the overall integrity of your aircraft's electrical 
system.

 

ℹ

Before initiating the power-up sequence, double-check to confirm that the battery is fully 
inserted into the battery compartment. Failure to securely position the battery could lead to 
unfortunate flight accidents during operation. Therefore, always ensure the battery is properly 
installed to guarantee safe and stable flight conditions.

ℹ

 

IMPORTANT

Содержание P100 Pro

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды