manualshive.com logo in svg

X-GLOO SE Series, Руководство пользователя, Страница: 11 / 18

Поделиться
Скачать
X-GLOO SE Series Скачать руководство пользователя страница 11

11

Phone:  +49 (0) 8641 6948 - 60

  

•

  

xgloo.com

  

•

  

 [email protected]

FOR XE 4/5/6

tent stakes

quantity

use

300 mm L

16 pcs.

walls

500 mm L

4 pcs.

outer tube

Dach

Reißverschluss-

abdeckung

Wand

4.4 WALL BALLASTS

The Wall Ballasts can be filled with water or sand/
gravel and can be connected to the wall using the 
attached toggles. 

FILLING WITH WATER

•   Open the velcro on the ballast cover and pull out the 

water bladder until the fill valve is visible.

•   There is a water bladder inside each ballast cover for 

filling with water. If filling the ballasts with sand or 
gravel, the water bladders must first be removed or 
they will become damaged.

•   Included in the Tube Ballast Set are a hose and 

various faucet adapters. Attach the hose to the 
faucet using the correct adapter.

•   Open the fill valve, insert the other end of the hose 

and fill the bladder with water.

•   Once full, remove the hose and close the valve and 

the velcro on the ballast cover.

•   Connect the four plastic toggles on the ballast to the 

large grommets on the wall. When doing so, make 
sure that the rubber-reinforced side of the Wall 
Ballast is facing down. For securing walls on XE 5 or 
XE 6 tents, the use of multiple wall ballasts on each 
wall is recommended.

water bladder

The following graphic shows which size/type tent stake should be used at which position.

wall

outer 

tube

roof

rain cover

wall

Содержание SE Series



















Отзывы:

Нет отзывов