Copyright © 2015 WyreStorm Technologies |
EX-SW-0201-4K Quickstart Guide | 160516
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
3 of 4
HDBaseT Wiring
IMPORTANT! Wiring Guidelines
• 4K UHD resolutions require more bandwidth than 1080p, for this reason
Wyrestorm recommends using Cat6 or higher to ensure proper 4K UHD
transmission.
• The use of patch panels, wall plates, cable extenders, kinks in cables,
and electrical or environmental interference can have an adverse effect
on HDMI and HDBaseT transmission limiting performance.
• If a patch panel is being used, Cat6a or higher cable must be used from
the matrix to the receiver as well as inside the panel to avoid loss of
signal.
•
While similar in nature, the HDBaseT protocol is different than Ethernet
and voltages provided for PoH can be higher than those provided by
PoE. For this reason, never connect an HDBaseT link to an Ethernet
router or switch to avoid damaging the connected devices.
Wiring for HDBaseT follows the EIA T568B standard.
Pin 1 Pin 8
Wire colors shown follow EIA/TIA-568B standard.
Pin 1:
Pin 2:
Pin 3:
Pin 4:
Pin 5:
Pin 6:
Pin 7:
Pin 8:
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
Resolution Distances
The type of category cable used and the distance between the matrix
and receiver can restrict the available video resolution.
Refer to
Video Resolutions
in the
distance based on resolution
.
RS-232 and Distance Settings
The Set dip-switches on the front panel on the TX and RX configure
RS-232 mode and Long Cable Mode.
•
Long Cable mode change must be made on both the TX and RX.
•
Switches that are grayed out in the images can be in any position
for the desired function.
RS-232 Pass-
through (Default)
RS-232 HDBT
Update
RS-232
Firmware Update
Long Cable
Mode Disabled
Long Cable
Mode Enabled
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
IR Wiring
IR TX (Emitter) Wiring
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
Tip:
IR Signal
Sleeve: Ground (GND)
IR RX (Receiver) Wiring
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that
o5V DC to power the included IR receiver.
IMPORTANT!
3rd party IR receivers may require a different voltage,
refer to the documentation provided with the IR receiver before making
any connections to avoid damaging the device.
Tip:
Ring:
IR Signal
+5V DC
Sleeve: Ground (GND)
RS-232 Wiring
RS-232 Connection Guidelines
The following wiring diagram shows the pinouts for the extender set.
While not shown, connect the TX (transmit) to RX (receive) pins at the
control system or PC side of the cable.
Most control systems and computers are DTE where pin 2 is RX, this can
vary from device to device. Refer to the documentation for the connected
device for pin functionally to ensure that the correct connections can be
made.
Wire colors shown follow EIA-561 standard.
Pin 1:
Pin 2:
TX (Transmit)
RX (Receive)
Pin 3:
Ground (GND)
1 2 3
Audio In/Out Wiring
Connection for Line In/Out uses a 3.5mm (1/8in) stereo jack.
Tip:
Ring:
Left Channel
Right Channel
Sleeve: Ground (GND)
EDID Settings
The
EDID
dip-switches located on the TX can be configured to resolve
issues with video output on displays that may not accept the maximum
resolution available from the source.
800x600
1024x768
1280x800
1920x1200
1920x1080
1280x720
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
