Attention:
We strongly recommend using the supplied
mounting brackets to secure both the transmitter and receiver
baluns. Sudden movement of these devices can lead to
unnecessary service call outs and loss of picture/sound due to
stress on connections.
HDMI: Connect the HDMI source (i.e. HD-DVD,
PS3, Cable/Sat box, Blu-ray etc.) to the HDMI IN of the
TRANSMITTER and connect the HDMI DISPLAY (i.e. LCD/
plasma TV, digital projector etc.) to the HDMI OUT of the
AMP-001-010 Receiver/Amplifier/Repeater (AMP).
Use good quality HDMI cables, ensuring connectors are
inserted firmly in ports and avoid excessive bending of cable.
Attention:
Do Not Hotswap! - Please insert and
extract cables carefully with the power SWITCHED OFF.
Connecting and disconnecting while the unit is powered can
result in damage to circuitry.
One-way IR: Position the small, round IR TX emitter directly
over the infrared receiving area of the SOURCE and secure
with the adhesive backing. You may need to adjust the location
of the emitter later to achieve best results - repositioning to
different areas on the source facia can sometimes improve IR
performance. Insert the IR TX 3.5mm jack into the IR TX port on
the TRANSMITTER.
HINT:
You can locate the small, round infrared sensor by
shining a flashlight onto the display panel of your source.
Insert the IR RX 3.5mm jack into the IR RX port on the
RECEIVER. Discretely attach the larger, rectangular IR eye to
the DISPLAY with the adhesive backing, ensuring a clear line of
sight to the remote control being used. Again, repositioning IR
RX may be required to achieve best results.
For two-way control of SOURCE and DISPLAY from both
locations, an IR TX eye should also be placed over the IR sensor
of the DISPLAY and an IR RX eye placed on the SOURCE.
Cat5e/6 Transmission: Connect the TRANSMITTER and
AMP with a single, good quality, well terminated and tested
Cat5e/6 cable with RJ45 connectors wired to 568B standard at
both ends up to a distance of 70m (230ft).
The quality of each RJ45 termination is essential - poor
termination leads to intermittent performance and longer install
times.
To extend transmission to another display zone, connect a
Cat5e/6 cable from the HDBT Out of the AMP up to 70m (230ft)
to another AMP (7 is max. number of AMPs connectable).
Attention:
Check connectors are pushed securely into each
port and supported by the connector strain relief clip to prevent
them from becoming loose.
Audio Connection: For enhanced audio capabilities,
connect the AMP to speakers, subwoofer, control system,
analog audio output and local audio input such as MP3 player
or multiroom audio system.
(See AMP-001-010 instruction
manual for full information on this product.)
Power: Add 5V power supply provided to TRANSMITTER
and 18v supply to the AMP.
We do not recommend passing power remotely over long cable
distances as this can affect product performance.
Finally, power on TRANMITTER, AMP and all connected
devices and your extender set is ready for use.
Attention:
Check LED POWER and STATUS are lit to confirm
the units are powered and a signal link is established between
the units. If not, check connections, devices and power supplies
or follow the troubleshooting overleaf.
1
2
3
4
5
6
7
WYRESTORM QUICKSTART INFORMATION SHEET
US OFFICE:
TEL: +1 901 384 3575
FAX: +1 901 384 3574
EMEA OFFICE:
TEL: + 44 (0) 1793 230 343
FAX: + 44 (0) 1793 230 583
WyreStorm ex-1utp-ir-70-AMP
Single 70m (230ft) HDBaseT two-way IR & RS232 Extender with Receiver/Amplifier/Repeater
*PLEASE NOTE
All cable distances
are on the basis of a
direct runs of cable
(no patch panels or
wall outlets). Please
use good quality, solid
conductor, Cat5e
cable. Standard pre-
made patch leads will
reduce effectiveness
of this product. Please
ensure Cat5e cables
are installed to local
electrical regulations.
Close lying electrical
cables can effect
product performance.
1
1
2
3
4
4
5
5
6
6
Power
Power
Local audio
input
Speakers
SUB
rs232
DISPLAY OUTPUT
hd
mi C
a
ble
hd
mi
C
a
ble
c
at
5
e
C
a
ble
cat5
e
Cable
to cascading
amplifier
IR TX C
a
ble
IR RX C
a
ble
TRANSMITTER
RECEIVER/
amplifier
SOURCE DEVICE
