manualshive.com logo in svg

wsm wg972-e4, Руководство по ремонту

Поделиться
Скачать
wsm wg972-e4 Скачать руководство пользователя страница 133

ENGINE

WG972-E4, WSM

1-S42

Valve Recessing

1. Clean the cylinder head, the valve face and seat.
2. Insert the valve into the valve guide.
3. Measure the valve recessing with a depth gauge.
4. If the measurement exceeds the allowable limit, replace the

valve.

5. If it still exceeds the allowable limit after replacing the valve,

replace the cylinder head.

9Y1211108ENS0066US0

Valve Seating

1. Coat the valve face lightly with prussian blue and put the valve

on its seat to check the contact.

2. If the valve seats all the way around the valve seat, the valve

seat is correct.

3. If the valve does not seat all the way around the valve seat,

lapping the valve as follows.

4. If the valve contact is incorrect after lapping the valve, replace

or correct the valve or correct the contact of valve seating.

9Y1211108ENS0067US0

Valve recessing (Intake 
and Exhaust)

Factory specification

0.10 (protrusion) to 
0.10 (recessing) mm 
0.0039 (protrusion) to 
0.0039 (recessing) in.

Allowable limit

0.30 (recessing) mm
0.012 (recessing) in.

(1) Cylinder Head Surface

(A) Recessing
(B) Protrusion

(1) Correct

(2) Incorrect

KiSC issued 07, 2015 A

Содержание wg972-e4


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды