manualshive.com logo in svg

wsm wg972-e4, Руководство по ремонту

Поделиться
Скачать
wsm wg972-e4 Скачать руководство пользователя страница 110

ENGINE

WG972-E4, WSM

1-S19

Resistance of Injector (Gasoline line) [WG972-GL, WG972-G]

1. Disconnect the connector.
2. Measure the resistance between terminals with an ohmmeter.
3. If the resistance is not with in the factory specifications, replace

it.

9Y1211108ENS0019US0

Resistance of Lock Off Valve (Gas line) [WG972-GL, WG972-L,
WG972-N]

1. Disconnect the connector.
2. Measure the resistance with an ohmmeter between the

connector terminals.

3. If the factory specification is not indicated the solenoid is

damaged.

9Y1211108ENS0033US0

(5) Ignition System

Resistance of Crankshaft Position Sensor

1. Disconnect the connector.
2. Measure the resistance with an ohmmeter.
3. If the resistance is not with in the factory specifications, replace

it.

NOTE

• This table shows the results of the test conducted by using

the "Sanwa-made testers SP-10 / SP-150" (analog meter).

• Use of other testers than those above may show different

measured results.

(When reassembling)

• Make sure to be connected firmly.

9Y1211108ENS0020US0

Conduction of Camshaft Position Sensor

1. Disconnect the connector.
2. Check the conduction of each pins.

NOTE

• It is a simple check way, so if you need in detail, check the

signal of camshaft position sensor with diagnostic tool.

9Y1211108ENS0021US0

Resistance

Factory specification

11.7 to 12.3 

Ω

at 20 °C (68 °F)

LPG cut off solenoid

Factory specification

Approx. 12.65 

Ω

 

at 20 °C (68 °F)

(1) LPG Lock Off Valve

Resistance

Factory 
specifica-
tion

A

 - 

B

1.85 to 2.45 k

Ω

 

at 20 °C (68 °F)

Conduction

Factory specification

Not conduction

KiSC issued 07, 2015 A

Содержание wg972-e4


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды