Worcester GR2300iW C Скачать руководство пользователя | Manualshive

Страница: 19 / 100

background image

Pre-Installation

19

Greenstar 2000 – 6 721 820 552 (2021/02)

Fig. 13 Reduced front maintenance clearances - Front view

[A]

Appliance.

[1]

Above appliance - Same clearance required as for standard
clearances of 60/100 flue or 80/125mm flue.

[3]

Bottom of appliance to the floor - 1,000 - 1,500mm.

[4]

Below appliance - 200mm

[5]

One side of appliance - Minimum 300mm.

[6]

One side of appliance - Minimum 5mm.

Appliances in compartments

Follow the latest requirements of BS6798 and BS5440 and note:
• Minimum clearances must be maintained.
• An access door is required to install, service and maintain the

appliance and any ancillary equipment.

• If the appliance is installed in an unventilated airing/storage

cupboard, there is no requirement to make a partition between the
appliance and the storage space as long as the minimum clearances
around the appliance are maintained.

4.4

Flue systems considerations

WARNING

Flue systems

Possible flue gas escape

▶ Use Worcester, Bosch Group approved Condensfit II flue systems

only, no other manufacturer’s flue have been tested or approved for
use with Worcester, Bosch Group appliances.

CAUTION

Concealed flue systems:

▶ Where a flue system is going to be concealed, provision must be

made for service and inspection.

▶ Voids containing concealed flues must have at least one inspection

hatch no less than 300mm square.

▶ Flue joints within the void must not be more than 1.5 metres from the

edge of the inspection hatch.

▶ Inspection hatches should be located at changes of direction.
▶ If this is not possible, bends should be viewable from both directions.

Refer to the manual supplied with the Worcester, Bosch Group flue kit for
complete installation instructions.

Flue kit part numbers

Table 13 Flue kit assembly part numbers

4.4.1

Flue length

Horizontal maximum flue lengths

Table 14 Maximum flue lengths - Horizontal flues

Vertical maximum flue lengths

Table 15 Maximum flue lengths - Vertical flues

0010031673-001

1

6

5

5

4

3

A

Part number

Flue Ø

Description

7 716 191 082 60/100

Telescopic horizontal flue kit

7 716 191 171 60/100

Extended telescopic horizontal flue kit

7 733 600 048 60/100

Horizontal high level telescopic flue kit

7 719 003 702 80/125

Telescopic horizontal flue kit

7 719 002 430 60/100

Vertical balanced flue kit

7 719 002 431 80/125

Vertical balanced flue kit

Flue length [L] Flue length [L]

Appliance

60/100

80/125

GR2300iW 25 C

9,000mm

12,000mm

GR2300iW 30 C

9,000mm

12,000mm

Flue length [L] Flue length [L]

Appliance

60/100

80/125

GR2300iW 25 C

12,000mm

15,000mm

GR2300iW 30 C

12,000mm

15,000mm

«
...
17
18
19
20
21
...
»

Содержание GR2300iW C





































































































Отзывы:

Нет отзывов

Похожие инструкции для GR2300iW C

Бренд: H2O Страницы: 50

Бренд: Raypak Страницы: 213

Salamander Broiler

Бренд: U.S. Range Страницы: 52

Бренд: HydroTherm Страницы: 24

Бренд: Pereko Страницы: 24

Бренд: Camus Hydronics Страницы: 82

Бренд: Nieco Страницы: 40

Бренд: Buderus Страницы: 168

Бренд: Nibe Страницы: 44

Main Combi 24 HE

Бренд: Baxi Страницы: 56

Бренд: Rinnai Страницы: 26

Бренд: Wood heating solution Страницы: 31

Бренд: Viessmann Страницы: 136

Mexico Slimline CF440

Бренд: Ideal Boilers Страницы: 36

LOGIC MAX COMBI 2 C24

Бренд: Ideal Heating Страницы: 68

Бренд: Electric Heating Company Страницы: 20

Бренд: Flexiheat Страницы: 63

Бренд: Knight Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды