Woodway ST PPS 43 Med Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 122

background image

43 | UM-PP-EN-03

6.3

Installation

It is recommended that transport, installation, and assembly of the treadmill are carried out by
WOODWAY or by an authorized dealer or service provider. Otherwise, shipping damage or improper
installation and assembly of the treadmill could cause a hazard when using the device.

ATTENTION

Prepare a Stable Surface

Before the device is installed, the surface must be prepared. The total
weight of the device (with all the accessories and options) is to be
considered.

►

Prepare a stable and sturdy surface.

►

Only install the device on a level, stable, and sufficiently sturdy
surface.

►

If necessary, install an additional base plate/floorboard.

The following further instructions for installation are to be observed:

•

When installed on upper floors, the device must be placed as far as possible in a corner of
the room so that sufficient stability is guaranteed, even at max. speed. The structure of the
building must be checked in advance.

•

The treadmill should not be installed close to a radiator or any other heat source.

•

Due to the moving parts on the underside, the device must not be placed directly on thick
or high-pile carpeting. In this case, a mat should be placed under the device. This will
prevent lint from entering into the treadmill and at the same time reduce carpet wear.
WOODWAY has appropriate mats available. For more information, call WOODWAY
Customer Service.

•

With larger PPS Series devices, particular attention must be paid to the ceiling/floor load
capacity at the installation site. This must be higher than the total weight (weight of the
device plus the dynamic weight of a running person) and approved by an authorized
authority with the treadmill representative.

«
...
47
48
49
50
51
...
»

Содержание ST PPS 43 Med



























































































































Отзывы:

Нет отзывов

Похожие инструкции для ST PPS 43 Med

CONCORD Express

Бренд: GE Interlogix Страницы: 32

Бренд: Unipar Страницы: 10

Бренд: VADDIO Страницы: 20

WallVIEW CCU HD-18 HD-SDI

Бренд: VADDIO Страницы: 18

Бренд: VADDIO Страницы: 60

Бренд: Vacron Страницы: 2

CLEARVIEW HD-18

Бренд: VADDIO Страницы: 4

Бренд: HAKO Страницы: 6

Бренд: LST Страницы: 1

360 GROUND FINDER Series

Бренд: S&C Страницы: 3

Бренд: Zamel Страницы: 2

Бренд: D-MAX Страницы: 47

EXPCMR-ALG-1080P-12V

Бренд: Larson Electronics Страницы: 4

ExoFit NEX 1113283

Бренд: DBI SALA Страницы: 28

ViP2 VK2-1080VFD3V9F

Бренд: Vista Страницы: 12

Бренд: Lorex Страницы: 2

Бренд: Argo Страницы: 7

MEGAPIXEL WIRELESS NETWORK CAMERA SERIES

Бренд: Avtech Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды