manualshive.com logo in svg

Woodward SPM-D2-10, Руководство пользователя

Поделиться
Скачать
Woodward SPM-D2-10 Скачать руководство пользователя страница 53

Manual 37615C 

SPM-D2-10 - Synchronizing Unit 

 

 

 

 

© Woodward 

Page 53/68 

 

Parameter 5505 

Phase matching 
Gain          00 

Phase matching control = ON 

Phase-angle-zero-control gain 

1 to 36 

This configuration screen only appears, if the phase matching control is configured 
ON! 
When phase matching control is enabled, this gain determines how much the output 
signal is changed depending on phase difference. By increasing the gain, the re-
sponse is increased to permit larger corrections to the variable to be controlled result-
ing in longer ON time periods. The farther out of tolerance the process is the larger 
the response action is to return the process to the tolerance band. If the gain is con-
figured too high, the result is excessive overshoot/undershoot of the desired value.  
Prior to setting the value for this gain, the frequency controller must be enabled and 
properly adjusted. 

 

Parameter 5506 

Phase matching 
df start  0.00Hz 

Phase matching control = ON 

Differential frequency for starting phase-angle-zero-control 

0.02 to 0.25 Hz 

This configuration screen is displayed only if the phase matching control is enabled! 
The control enables phase matching when the generator and busbar/mains frequency 
differential falls below the value configured here. 

Synchronization Time Monitoring 

 

Parameter 3060 

Sync.time contr. 
Alarm       ON 

Synchronization time monitoring 

ON/OFF 

ON

 ................ The synchronization timer is enabled. When a synchronization opera-

tion is initiated, this timer starts to count down. If the timer expires 
prior to the synchronization being completed and the breaker closing, 
the warning message "Synchronization time" is displayed. In addition 
to the warning message the “Ready for operation" relay is de-energized 
and the synchronization operation is terminated. The alarm condition 
may be reset by pressing and holding the "Clear" pushbutton for at 
least 3 seconds or removing one of the required conditions for syn-
chronization (e.g. de-energize terminal 3 "Release CB"). The subse-
quent screens of this function are displayed. 

OFF

 .............. The synchronization time is not monitored and the control will contin-

ue to attempt to synchronize until the circuit breaker is successfully 
closed or the synchronization it terminated. The subsequent screens of 
this function are not displayed. 

 

Parameter 3063 

Sync.time contr. 
Delay time 000s 

Final value for synchronization time monitoring 

10 to 999 s 

If the synchronization time monitoring has been enabled, the control will attempt to 
synchronize for up to the time period configured here. 

 

Содержание SPM-D2-10





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды