manualshive.com logo in svg

Woodward SPM-D2-10, Руководство пользователя

Поделиться
Скачать
Woodward SPM-D2-10 Скачать руководство пользователя страница 36

Manual 37615C 

SPM-D2-10 - Synchronizing Unit 

 

 

 

 

Page 36/68 

© Woodward 

LC Display 

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡ 

 

15

 

LC-Display 

LC-Display 

The two-line LC display outputs corresponding text messages and values de-
pending on the mode that the SPM-D2 is operating. In the configuration 
mode, the monitoring parameters may be changed. When the SPM-D2- is in 
the automatic mode, the measured values are displayed. 

Display Monitoring in Automatic Mode: Double Voltage / Frequency Display 

LCD type 1 

(V configured) 

B: 000 V 00.00Hz 
G: 000 V 00.00Hz 

 

LCD type 2 

(kV configured) 

B:00.0kV 00.00Hz 
G:00.0kV 00.00Hz 

Double voltage and double frequency displays, Generator values 

The generator (variable system) and reference voltage and frequency are displayed in 
this screen. The phase angle between the generator and reference voltage is displayed 
by the synchroscope (LED strip). 
 

B

 ....... Reference voltage and frequency 

G

 ....... Generator (variable system) voltage and frequency 

 

LCD type 1 

(V configured) 

M: 000 V 00.00Hz 
   000 V   000 V 

 

LCD type 2 

(kV configured) 

M:00.0kV 00.00Hz 
  00.0kV 00.0kV 

Mains values 

Mains voltage and mains frequency are monitored. 
 

M

 ...... Mains voltage and mains frequency 

 

 upper line: 

    - Phase voltage L1-L2 
    - Frequency 

 bottom line: 

    - Phase voltage L2-L3 
    - Phase voltage L3-L1 

Display Monitoring in Automatic Mode: Alarm Indication 

---------------- 
xxxxxxxxxxxxxxxx 

Alarm indication, bottom line 

The indications are displayed according to the following list: 

 

Type of alarm 

Displayed text 

Synchronization time is exceeded 

Synchr. time

 

 

Содержание SPM-D2-10





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды