manualshive.com logo in svg

Woodward SPM-D11, Руководство пользователя

Поделиться
Скачать
Woodward SPM-D11 Скачать руководство пользователя страница 25

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

© Woodward 

Page 25/79 

Synch-Check 

In this condition, the unit can be used as a check-synchronizer. No control is carried out. The relay "Command: 
CB close" remains energized, as long as the following conditions are met: 
 

•

  The configured limit for the voltage difference is met 

(screen "synchronization dV

max

) 

•

  The configured limits for the frequency difference are met 

(screen "synchronization df

max

 and df

min

") 

•

  The configured limit for the phase angle is met 

(screen "slip synchroniz. phase

max

") 

•

  The input "Reply: CB is open" is energized 

•

  The parameter "Terminal 6" is configured to "Release control" 

•

  The terminal 6 is not energized (the control is disabled) 

•

  The input "Enable isolated operation / dead bus start" is energized 

•

  The input "Enable CB" is energized 

The synchronization time monitoring is disabled. 

Isolated Operation 

The generator voltage and frequency are controlled according to the configurable set point values. The generator 
breaker is closed. To activate the voltage controller, the parameter "volt. controller in isol. oper." must be set to 
"ON". To activate the frequency controller, the parameter "freq. controller in isol. oper." must be set to "ON". 
Additionally, the discrete input "Enable isolated operation / dead bus start" must be energized to enable isolated 
operation. 

Closing the CB Without Synchronization (Dead Bus Start) 

A close command for the power circuit breaker will be output without synchronization if the following condi-
tions are met: 
 

•

  The control is in the automatic mode (LED "Automatic" lights up) 

•

  The parameter "

Gen. circ.break. Dead bus op.

" has been set to "

ON

" 

•

  The bus bar is not energized (V

SS

 < 5 % V

N

) 

•

  The generator voltage and frequency are within the configured limits 

•

  The input "Enable isolated operation / dead bus start" is energized 

•

  The input "Enable CB" is energized 

•

  The input "Reply: CB is open" is energized 

 

Содержание SPM-D11
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды