background image

Parts List:

Please identify and verify that you have all of the 

hardware shown below prior to assembly.

Parts listed below are not shown in the hardware 

drawings. Refer to photos in the instructions:

Part Description 

Quantity

3210A 

15-7/8” One Track . . . . . . . . . . . . . . . . . 1

3210B 

5-5/8” sq. Axis Base, MDF . . . . . . . . . . 1

3210C 

7-5/8” sq. Axis Base, MDF . . . . . . . . . . 1

3210P 

Pivot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4206 

6” One Track . . . . . . . . . . . . . . . . . . . . . . 1

4212 

12” One Track . . . . . . . . . . . . . . . . . . . . . 1

3205B 

Scribe Pencil Holder . . . . . . . . . . . . . . . 1

3210

 Small Oval Jig 

Owners Manual

Please Read Carefully!

Part# Description Qty.

5760B 1/4-20 

Oval 

Nut 

2

Part# Description Qty.

MP043 7/16” 

Screw  2

Part# Description Qty.

SFP008 1” 

Screw 

4

Part# Description Qty.

5750B 10-24 

Oval 

Nut 

2

Part# Description Qty.

MF005 1/2” 

Screw 

1

Part# Description Qty.

5505 

3/4” Thumb Screw  2

Part# Description Qty.

5765B Offset 

Oval 

Nut 

1

Part# Description Qty.

BUSH001 1/8" 

Spacer 

2

Содержание 3210

Страница 1: ...q Axis Base MDF 1 3210P Pivot 2 4206 6 One Track 1 4212 12 One Track 1 3205B Scribe Pencil Holder 1 3210 Small Oval Jig Owners Manual Please Read Carefully Part Description Qty 5760B 1 4 20 Oval Nut 2 Part Description Qty MP043 7 16 Screw 2 Part Description Qty SFP008 1 Screw 4 Part Description Qty 5750B 10 24 Oval Nut 2 Part Description Qty MF005 1 2 Screw 1 Part Description Qty 5505 3 4 Thumb Sc...

Страница 2: ... the thumb screws Insert a 7 16 Screw MP043 thru both of the Pivots 3210P and start a 10 24 Oval Nut 5750B on the end of each screw See fig 3 Slide the Pivots into the open end of 16 One Track Their position on the One Track will depend on the size and differential of the oval you need to make Slide the 16 One Track into the groove in the work table that s clamped to the table of your sander Slide...

Страница 3: ...ase with 1 screws STP008 or double face tape SANDING OVALS Slide the 16 One Track away from the sanding surface Rotate the Inside Pivot so it s at a right angle to the One Track and rotate the Outside Pivot so it s in line with the One Track See fig 5 Set the Axis Base work on the Pivots with the long axis of the work at a right angle to the One Track Slip the groove in the Axis Base that lines up...

Страница 4: ...pencil in the pencil holder to draw the desired oval See fig 9 TECHNICAL STUFF When cutting a 4 wide oval frame for example the frame will only measure 4 at the 0º 90º 180º 270º points It will measure slightly narrower everywhere else This phenomenon is common to all oval jigs Actually the jig is cutting 4 wide everywhere but that s measured on the center line of the grooves in the Axis Base which...

Отзывы: