Wood Stone FIRE DECK 6045 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 44

background image

Fire Deck

Service Manual

PG

38

OF

44

M0011.09 APRIL 2019

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TOLL FREE

800.988.8103

TEL

360.650.1111

FAX

360.650.1166

E-MAIL

[email protected]

woodstone-corp.com

ELECTRICAL CONNECTIONS

ELECTRICAL

The incoming 120 VAC 15 A electrical connection is made beneath the oven at the terminal strip inside the transformer box (9690,
11290, 11275), or at the junction box located at the rear left or right side all other Fire Deck models� An external cover plate provides
access to this junction box� Wiring diagrams may be found inside the Control Box, and on the transformer cover plate� Export models
may have different electrical requirements, which will be clearly marked on the wiring diagrams and the Transformer Plate�

ELECTRICAL CODE LIMITATIONS

Electrical grounding:

This appliance must be electrically grounded in accordance with local codes, or in the absence of local codes,

with the National Electrical code, ANSI NFPA 70 or the Canadian Electrical Code, CSA C22�1 as applicable�

INTERLOCKING

If it is necessary to interlock the oven with an exhaust fan, Wood Stone recommends the following: Wire the installation in such a
way that incoming 120 VAC power to the oven is supplied only when the exhaust fan is turned on� A two pole switch controlling the
power to the fan and to the oven may be used� Consult a qualified electriciian� NEVER attempt to wire into the oven Control Box or low
voltage junction box�

ADDING TO OR ALTERING ANY OF THE WIRING IN THE OVEN CONTROL BOX OR LOW VOLTAGE JUNCTION

BOX WILL VOID THE WARRANTY.

Please call Wood Stone if you have any questions�

«
...
36
37
38
39
40
...
»

Содержание FIRE DECK 6045













































Отзывы:

Нет отзывов

Похожие инструкции для FIRE DECK 6045

Бренд: Falcon Страницы: 17

Big Mouth Duo Plus

Бренд: Hamilton Beach Страницы: 32

Big Mouth Duo Plus

Бренд: Hamilton Beach Страницы: 20

Бренд: Waring Страницы: 4

Бренд: Waring Страницы: 13

Бренд: Linea 2000 Страницы: 44

Party Pan 61492

Бренд: Ellrona Страницы: 66

Бренд: Paderno Страницы: 14

Бренд: Cuisinart Страницы: 17

ThermoBlend 2 KATHMXBENXA

Бренд: Kogan Страницы: 13

Бренд: lancer Страницы: 12

Бренд: Sunbeam Страницы: 12

Бренд: SEVERIN Страницы: 68

Бренд: Wamife Страницы: 7

Бренд: Amica Страницы: 23

Бренд: Unold Страницы: 88

Бренд: STARFRIT Страницы: 13

Бренд: Vollrath Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды