manualshive.com logo in svg

Wood Stone FIRE DECK 6045, Руководство по обслуживанию

Деревянная каменная печная площадка 6045 предлагает высокое качество и стильный дизайн для домашнего отопления. Бесплатное руководство по обслуживанию доступно для скачивания на {вебсайте}, чтобы помочь вам получить максимум от вашей печи. Узнайте, как правильно ухаживать за вашим обогревателем.

Поделиться
Скачать
background image

 

PG 

37 

OF

 44

M0011.09    APRIL 2019

Fire Deck  

Service Manual

GAS CONNECTIONS

IF YOU ARE CONVERTING A WOOD STONE OVEN FROM LP TO NATURAL GAS, OR NATURAL GAS TO LP, CONTACT THE WOOD 

STONE SERVICE DEPARTMENT TO OBTAIN THE NECESSARY PARTS TO CARRY OUT THIS PROCEDURE. THIS PROCEDURE 

ENTAILS CHANGING THE BURNER JETS, PILOT ORIFICES AND GAS VALVE REGULATOR SPRINGS, AS WELL AS ADJUSTING THE 

BURNER MANIFOLD PRESSURES AS SPECIFIED FOR THE NEW GAS TYPE. 

GAS CONNECTION

The Fire Deck 8645 and 6045 come equipped with a 3/4" FNPT connection� All gas piping up to the oven must have a minimum 
inside diameter of 3/4", including all fittings and shut off valves, which should be of the full flow type�
The Fire Deck 9690, 11290, 11275, 9660, 11260 models are equipped with a 1" FNPT gas connection� All gas piping up to the oven 
must have a minimum inside diameter of 1", including all fittings and shut off valves, which should be of the full flow type� 
Have a licensed gas installer provide the hook-up and test all fittings and pipe connections for leaks� Use approved gas leak detectors 
(soap solutions or equivalent) over and around the fittings and pipe connections� 

DO NOT USE A FLAME TO TEST FOR LEAKS! 

Wood Stone recommends that the Fire Deck be equipped with a manual, individual shutoff valve, located between the oven and 
the main gas supply, and that this shutoff valve (supplied by others) be left readily accessible� Wood Stone also recommends that 
inspection and maintenance of the Burners and gas piping connections of this appliance be performed at regularly scheduled 
intervals and only by professional gas appliance service agencies�

GAS INLET PRESSURE

For ovens running on natural gas, an inlet pressure of 7 to 10" W�C� is recommended to ensure optimum oven performance� Incoming 
gas pressure below this range will affect oven performance, the lower the pressure the greater the negative impact� If the gas supply 
pressure is greater than 14" W�C� (1/2 psi), an external regulator, supplied by others, is REQUIRED to lower the gas pressure to the 
acceptable range� Issues caused by low or high gas pressure are installation issues, and will not be covered under the Warranty�
For ovens running on Propane (LP or HLP), the recommended inlet pressure to ensure optimum oven performance is 10 to 12" 
W�C� Incoming gas pressure below this range will affect oven performance, the lower the pressure the greater the negative impact� 
If the gas supply pressure is greater than 14" W�C� (1/2 psi), an external regulator, supplied by others, is REQUIRED to lower the gas 
pressure to the acceptable range� Issues caused by low or high gas pressure are installation issues, and will not be covered under the 
Warranty�
For all installations, follow best practices for proper gas line pipe sizing for the line serving the oven� To insure proper operation, all gas 
piping and fittings leading up to the oven should have an inside diameter equal to or greater than that of the oven gas connection� Also 
make sure that a readily accessible shut off valve (supplied by others) is installed near the oven, and in accordance with all applicable 
codes� Shut off valves must be of the full-flow type, and not introduce any restriction into the gas line� 
The connection to the oven should be hard-piped whenever feasible� If this is not possible, use a properly sized flexible connector 
approved for this application� When using a flexible connector make sure that its design does not present any reduction in pipe 
diameter or other restriction� Oven issues caused by improper pipe sizing, improper shut off valves, restrictive connectors, or any other 
deficiency in the gas supply design or installation will not be covered under the oven warranty�

GAS CODE LIMITATIONS

The installation of this appliance must conform with local codes, or in the absence of local codes, with the National 

Fuel Gas Code, ANSI Z223.1 or The Natural Gas Installation Code CAN/CGA-B149.1 as applicable. 

The appliance and its individual shutoff valve (supplied by others) must be disconnected from the gas supply piping system during any 
pressure testing of that system at test pressures in excess of 1/2 psi (14" W�C�) (3�45 kPa)� 
The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve (supplied by others) 
during any pressure testing of the gas supply piping system at test pressure, equal to or less than 1/2 psi (14" W�C�) (3�45 kPa)�

Maximum inlet gas pressure must not exceed 14" W.C. (1/2 psi)

Содержание FIRE DECK 6045













































Отзывы:

Нет отзывов

Похожие инструкции для FIRE DECK 6045

Roundup HDC 9300300 Owner'S Manual preview
HDC 9300300
Бренд: Roundup Страницы: 20
Feel-Maestro Classic MR 1722 Owner'S Manual preview
Classic MR 1722
Бренд: Feel-Maestro Страницы: 24
Garland GTOG12-2 Installation And Operation Manual preview
GTOG12-2
Бренд: Garland Страницы: 48
HURAKAN HKN-WNC128CW Manual preview
HKN-WNC128CW
Бренд: HURAKAN Страницы: 61
Sammic OS-10 User Manual preview
OS-10
Бренд: Sammic Страницы: 8
Gastroback Design Fleischwolf Pro M Operating Instructions Manual preview
Design Fleischwolf Pro M
Бренд: Gastroback Страницы: 56
Parkinson Cowan RENOWN S 50 Installation Instructions Manual preview
RENOWN S 50
Бренд: Parkinson Cowan Страницы: 40
IKEA STEKA Manual preview
STEKA
Бренд: IKEA Страницы: 36
ENKHO 140924.01 User Manual preview
140924.01
Бренд: ENKHO Страницы: 40
Beer Meister BM-1600 Instruction Manual preview
BM-1600
Бренд: Beer Meister Страницы: 22
Presto HomeAde 2621 Instructions preview
HomeAde 2621
Бренд: Presto Страницы: 4
amzchef P-001 Instruction Manual preview
P-001
Бренд: amzchef Страницы: 7
Inkbird ISV-100W Manual preview
ISV-100W
Бренд: Inkbird Страницы: 75
CALOR DT71 Series Manual preview
DT71 Series
Бренд: CALOR Страницы: 41
Bluestone VSB-2735 User Manual preview
VSB-2735
Бренд: Bluestone Страницы: 11
Vacmaster VP680 User Manual preview
VP680
Бренд: Vacmaster Страницы: 24
Cookology CWC605BK Instruction Manual preview
CWC605BK
Бренд: Cookology Страницы: 13
Jupiter JUPITER System Operating Instructions Manual preview
JUPITER System
Бренд: Jupiter Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды