Wood Stone FIRE DECK 6045 Скачать руководство пользователя страница 3

Страница: 3 / 44

Fire Deck

Service Manual

M0011.09 APRIL 2019

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TOLL FREE

800.988.8103

TEL

360.650.1111

FAX

360.650.1166

E-MAIL

[email protected]

woodstone-corp.com

CAUTIONS & WARNINGS

WOOD STONE OVEN SERVICE MANUAL FOR GAS-FIRED,

WOOD-FIRED AND COAL-FIRED FIRE DECK SERIES OVENS

ADDITIONAL COPIES AVAILABLE UPON REQUEST

IF THIS OVEN IS NOT PROPERLY INSTALLED A FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE,

FOLLOW THESE INSTALLATION INSTRUCTIONS. A MAJOR CAUSE OF OVEN RELATED FIRES IS

FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS.

IT IS OF THE UTMOST IMPORTANCE THAT THIS OVEN BE INSTALLED ONLY IN ACCORDANCE

WITH THESE INSTRUCTIONS.

Wood Stone’s Fire Deck Gas-Fired ovens have been tested and approved by Intertek Testing

Services, and are ETL Listed to ANSI Z83.11:2016 Ed. 4, CSA 1.8:2016 Ed. 4, UL Subject 2162,

ULC-S627-00, UL 737 and to NSF/ANSI 4:2016.

IMPORTANT:

Consult your local gas supplier for a statement outlining a procedure to be followed in the

event you smell gas. Post the statement in a prominent location.

This manual is for use only by trained, qualified service personnel. It is recommended that this oven be

installed, maintained and serviced by qualified professionals.

FOR YOUR SAFETY:

Do not store or use gasoline or other flammable vapors or liquids in the vicinity of

this or any other appliance.

ESURE DE SÉCURITÉ:

Ne pas entreposer ni utiliser de’essence ni autres vapeurs ou liquides

inflammables à proximté de cet appareil ou de tout autre appareil.

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause property

damage, injury or death. Read the installation, operation and maintenance instructions thoroughly before
installing or servicing this equipment.

AVERTISSEMENT:

L’installation, le réglage, la modification, la réparation ou l’entretien incorrect de

cet appareil peut causer des dommages matériels, des blessures ou la mort. Lire attentivement les
instructions d’installation, de fonctionnement et d’entretien avant de procéder à son installation ou
entretien.

Also, always keep the area under and around this appliance free and clear of any and all combustible materials.

Содержание FIRE DECK 6045













































Результаты поиска

Содержание FIRE DECK 6045

Отзывы:

Похожие инструкции для FIRE DECK 6045

Бренды по названию

Популярные бренды

Wood Stone FIRE DECK 6045, Руководство по обслуживанию

Результаты поиска

Содержание FIRE DECK 6045

Отзывы:

Похожие инструкции для FIRE DECK 6045

Бренды по названию

Популярные бренды