manualshive.com logo in svg
  • Главная
  • /
  • Wood-mizer
  • /
  • LT40HD-R
  • /
  • Инструкция по безопасности, установке, эксплуатации и техническому обслуживанию

Wood-mizer LT40HD-R, Инструкция по безопасности, установке, эксплуатации и техническому обслуживанию

Поделиться
Скачать
Wood-mizer LT40HD-R Скачать руководство пользователя страница 88

Maintenance

Brake Strap Adjustment

5

5-16

HD-R04doc041910

Maintenance

5.10 Brake Strap Adjustment

WARNING! 

Before performing service near moving parts

such as blades, pulleys, motors, belts and chains, first turn
the key switch to the OFF (#0) position and remove the key.
If the key is turned on and moving parts activated, serious
injury may result.

Check the brake strap for wear every 200 hours of operation. Replace if damaged or
worn.

Also check and adjust the brake strap after each drive belt adjustment, if the blade does
not stop quickly, or unusual sounds occur when the brake is applied. Adjust the brake
strap if the drive belt jumps from the drive pulley when the autoclutch is disengaged.

1.

To access the brake strap, remove the belt cover located underneath the engine.

2.

Engage the autoclutch. 

See Figure 5-8. 

3.

Loosen the two nuts on the upper brake strap bracket. Slide the bracket and brake strap
down 1/8” and retighten the bracket nuts.

4.

Disengage the clutch. Check the drive belt fit in the drive pulley. You should just be able
to pull the belt from the pulley. If the belt is still too loose, engage the clutch and repeat
brake strap adjustments in 1/8” increments until the drive belt properly fits in the drive pul-
ley with the clutch disengaged.

NOTE:

 Be careful to not overtighten. Overtightening will cause the drive belt to “grab” the

pulley and can prevent the engine from starting properly.

5.

Replace the belt cover.

FIG. 5-8

200

Adjust bracket
down to tighten
brake strap

3H0169

Upper Brake Strap
Bracket Bolts

Содержание LT40HD-R







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды