manualshive.com logo in svg
  • Главная
  • /
  • Wood-mizer
  • /
  • LT40HD-R
  • /
  • Инструкция по безопасности, установке, эксплуатации и техническому обслуживанию

Wood-mizer LT40HD-R, Инструкция по безопасности, установке, эксплуатации и техническому обслуживанию

Поделиться
Скачать
Wood-mizer LT40HD-R Скачать руководство пользователя страница 134

Troubleshooting Guide

Engine/Motor and Drive Pulleys Alignment

6

6-25

HD-R04doc041910

Troubleshooting Guide

6.12 Engine/Motor and Drive Pulleys Alignment

WARNING! 

Before performing service near moving parts

such as blades, pulleys, motors, belts and chains, first turn
the key switch to the OFF (#0) position and remove the key.
If the key is turned on and moving parts activated, serious
injury may result.

WARNING!

 Do not for any reason adjust the engine drive

belts or belt support bracket with the engine running. Doing
so may result in serious injury.

1.

Install and properly tension the drive belt (

See Section 5.8

).

2.

With the autoclutch disengaged, use a straight edge to check the alignment of the pulley
on the engine to the alternator pulley. Loosen the bushing on the engine pulley and adjust
if necessary until it is aligned with the alternator pulley.

3.

With the autoclutch disengaged, use a straight edge to check the alignment of the engine
pulley to the main drive pulley. Loosen the bushing on the drive pulley and adjust if neces-
sary until it is aligned with the engine pulley.

4. (G25/G28 Only): 

Check that the engine pulley is also square with the drive pulley. If nec-

cessary, loosen the engine mounting bolts and cock the engine until the pulley is square
with the drive pulley. Retighten the engine mounting bolts.

5.

Check that all engine mounting bolts and pivot bushing clamps are tight. 

6.

Engage the autoclutch and recheck the pulley alignment. Adjust if necessary. 

7.

If any pulleys were adjusted, recheck the drive belt support(s) and adjust if neccessary
(

See Section 5.8

). 

Содержание LT40HD-R







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды