Wood-mizer LT15WB D17 Скачать руководство пользователя

Страница: 83 / 88

Sawmill Alignment

Blade Guide Horizontal Tilt Adjustment

Sawmill Alignment

1510doc071918

5-19

Blade Guide Horizontal Tilt Adjustment

If the blade guides are tilted in the wrong direction horizontally, the back of the blade may contact
the flange as the roller is spinning down, causing it to push the blade away from the guide roller.

Remove the blade guide alignment tool from the blade and adjust the blade guide arm halfway in.

Remove the clip from the blade guide alignment tool. Place the tool against the face of the outer
blade guide roller.

See Figure 5-23.

Measure between the back edge of the blade and the tool at the end closest to the inner blade
guide ("B").

Measure between the back edge of the blade and the other end of the tool ("A").

The roller should be tilted slightly to the left (’A’ 1/8" [3 mm] less than ’B’ ±1/8" [3 mm]).

FIG. 5-23

3H0802-5B

Blade Guide
Alignment Tool

Содержание LT15WB D17

























































































Результаты поиска

Содержание LT15WB D17

Отзывы:

Похожие инструкции для LT15WB D17

Бренды по названию

Популярные бренды

Wood-mizer LT15WB D17, Инструкция по безопасности, установке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LT15WB D17

Отзывы:

Похожие инструкции для LT15WB D17

Бренды по названию

Популярные бренды