Wood-mizer LT15WB D17 Скачать руководство пользователя

Страница: 21 / 88

Safety & General Information

Check sawmill Before Operation

Safety & General Information

doc071918

1-7

Check sawmill Before Operation

DANGER!

Make sure all guards and covers are in place and secured

before operating the sawmill. Failure to do so may result in serious
injury.

Keep Persons Away

DANGER!

Keep all persons out of the path of moving equipment and

lumber when operating the sawmill. Failure to do so will result in
serious injury.

DANGER!

Always be sure all persons are out of the path of the blade

before starting the motor. Failure to do so will result in serious injury.

WARNING!

Allow blade to come to a complete stop before opening

the blade housing cover. Failure to do so will result in serious injury.

Содержание LT15WB D17

























































































Результаты поиска

Содержание LT15WB D17

Отзывы:

Похожие инструкции для LT15WB D17

Бренды по названию

Популярные бренды

Wood-mizer LT15WB D17, Инструкция по безопасности, установке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LT15WB D17

Отзывы:

Похожие инструкции для LT15WB D17

Бренды по названию

Популярные бренды