Wood-mizer LT15WB D17 Скачать руководство пользователя | Manualshive

Страница: 15 / 88

background image

Safety & General Information

Blade Handling

Safety & General Information

doc071918

1-1

1

SECTION 1 SAFETY & GENERAL INFORMATION

This symbol calls your attention to instructions concerning your personal safety. Be sure to observe
and follow these instructions. This symbol accompanies a signal word. The word

DANGER

indicates

an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

suggests a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION

refers to potentially hazardous situations which, if not avoided, may result

in minor or moderate injury to persons or equipment. Read all safety instructions before operating
this equipment and observe all safety warnings!

Warning stripes are placed on areas where a single decal would be insufficient. To avoid serious
injury, keep out of the path of any equipment marked with warning stripes.

Read and observe all safety instructions before operating this equipment! Also read any additional
manufacturer’s manuals and observe any applicable safety instructions including dangers, warnings,
and cautions.

Always be sure that all safety decals are clean and readable. Replace all damaged safety decals to
prevent personal injury or damage to the equipment. Contact your local distributor, or call your
Customer Service Representative to order more decals.

IMPORTANT!

It is always the owner's responsibility to comply with all applicable federal, state and

local laws, rules and regulations regarding the ownership and operation of your Wood-Mizer sawmill.
All Wood-Mizer mill owners are encouraged to become thoroughly familiar with these applicable laws
and comply with them fully while using the mill.

Always properly dispose of all sawing by-products, including sawdust and other debris, coolant, oil,
fuel, oil filters and fuel filters.

Safety instructions are listed in this section by the following operations:



Blade Handling



Sawmill Setup



Sawmill Operation



Sawmill Maintenance

1.1

Blade Handling

DANGER!

Always disengage the blade and shut off the sawmill engine

before changing the blade. Failure to do so will result in serious injury.

WARNING!

Always wear gloves and eye protection when handling

bandsaw blades. Changing blades is safest when done by one person!
Keep all other persons away from area when coiling, carrying or
changing a blade. Failure to do so may result in serious injury.

«
...
13
14
15
16
17
...
»

Содержание LT15WB D17

























































































Отзывы:

Нет отзывов

Похожие инструкции для LT15WB D17

Бренд: EarthQuake Страницы: 36

Бренд: Scheppach Страницы: 53

Бренд: MTD Страницы: 10

Бренд: MTD Страницы: 12

Бренд: MTD Страницы: 15

Бренд: Central Machinery Страницы: 16

Бренд: Split-fire Страницы: 23

Бренд: Toro Страницы: 48

Бренд: Scheppach Страницы: 79

Бренд: Iron & Oak Страницы: 23

Бренд: Iron & Oak Страницы: 23

Бренд: Iron & Oak Страницы: 42

Бренд: Iron & Oak Страницы: 42

Бренд: Iron & Oak Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды