Wood-mizer CBT-430 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 46

Wood-mizer CBT-430 Скачать руководство пользователя страница 10

Safety

Safety Instructions

2

2-2

TL04doc081916

Safety

2.2

Safety Instructions

NOTE:

ONLY safety instructions regarding personal injury are listed in this section. Cau-

tion statements regarding only equipment damage appear where applicable throughout
the manual.

OBSERVE SAFETY INSTRUCTIONS

IMPORTANT!

Read the entire Owner's Manual before operating

the Tailer. Take notice of all safety warnings throughout this manual
and those posted on the machine. Keep this manual with this
machine at all times, regardless of ownership.

Also read any additional manufacturer’s manuals and observe any
applicable safety instructions including dangers, warnings, and
cautions.

Only persons who have read and understood the entire operator's
manual should operate the Tailer. The Tailer is not intended for use
by or around children.

IMPORTANT!

It is always the

owner's responsibility to comply
with all applicable federal, state
and local laws, rules and regula-
tions regarding the ownership
and operation of your Conveyor.
All owners are encouraged to
become thoroughly familiar with
these applicable laws and com-
ply with them fully while using the
Conveyor.

SETUP

WARNING!

Use extreme care and proper equipment to lift and

move the tailer. Lift under the base of the machine only. Failure to
do so may result in personal injury and/or machine damage.

WEAR SAFETY CLOTHING

WARNING!

Secure all loose clothing and jewelry before operating

the Tailer. Failure to do so may result in serious injury or death.

«
...
8
9
10
11
12
...
»

Содержание CBT-430















































Отзывы:

Нет отзывов