Wood-mizer BMS25 Скачать руководство пользователя страница 5

Страница: 5 / 59

Introduction

About This Manual

Introduction

WM doc 1/20/21

1-1

SECTION 1 INTRODUCTION

1.1

About This Manual

This manual replaces any previous information received on your Wood-Mizer

equip-

ment.

The information and instructions in this manual do not amend or extend the limited war-
ranties for the equipment given at the time of purchase.

1.2

Getting Service

General Contact Information

Toll free phone numbers are listed below for the

continental

U.S. and Canada.

Office Hours:

All times are Eastern Standard Time.

Please have your customer and serial number ready when you call.

Wood-Mizer will accept these methods of payment:



Visa, Mastercard, or Discover



COD



Prepayment

1.Wood-Mizer

is a registered trademark of Wood-Mizer LLC.

U.S. Patent No. 6,655,429.

United States

Canada

Sales

1-800-553-0182

1-877-866-0667

Service

1-800-525-8100

1-877-866-0667

Website

www.woodmizer.com

www.woodmizer.ca

E-mail

[email protected]

Monday - Friday

Saturday

(Indianapolis Office Only)

Sunday

8 a.m. to 5 p.m.

8 a.m. to 12 p.m.

Closed

Содержание BMS25




























































Результаты поиска

Содержание BMS25

Отзывы:

Бренды по названию

Популярные бренды

Wood-mizer BMS25, Инструкция по безопасности, эксплуатации, техническому обслуживанию и запасным частям.

Результаты поиска

Содержание BMS25

Отзывы:

Бренды по названию

Популярные бренды