manualshive.com logo in svg
  • Главная
  • /
  • Wood-mizer
  • /
  • BMS25
  • /
  • Инструкция по безопасности, эксплуатации, техническому обслуживанию и запасным частям.

Wood-mizer BMS25, Инструкция по безопасности, эксплуатации, техническому обслуживанию и запасным частям.

Поделиться
Скачать
Wood-mizer BMS25 Скачать руководство пользователя страница 15

WM doc 1/20/21

3-1

3

SECTION 3   ASSEMBLY

The Wood-Mizer

®

 BMS25 is shipped preassembled. Additional assemblies and parts 

include:

Three Upper Legs

Three Lower Legs

Three Compression Couplings

Three Blade Support Arms (with one bolt and two nuts attached to each)

One Wiring Harness

One Grinding Wheel

One Dressing Stone

One Multi-Angle Template

Blade Support Bag Assembly

Leg Bag Assembly

Blade Support Bag Assembly 

Contents

Qty.

Bolt, M6-1.0x35mm Class8 HH

6

Guide, Blade Support W/ Post

3

Ring, 1/4 Pushnut

3

Wheel, Blade Support

3

Nut, M6-1.0 Flange Hex Nylock 

Zinc

3

Nut, Wing M6x1 Zinc

3

Guide, Blade Support W/O Post

3

Leg Bag Assembly Contents

Qty.

Bolt, M6-1.0 x 40 Carriage

6

Nut, Wing M6x1 Zinc

6

Содержание BMS25




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды