Wolf Garten Ambition Robo Scooter 300, Оригинальная инструкция по эксплуатации

Страница: 80 / 306

9.2 Detailed Error Codes
If the above table (Section 9.1) does not give enough information to help solve the problem, then press the RIGHT arrow
while the error code is displayed in order to receive a number that gives more details about the problem and refer to the table
below:
ŝƐƉůĂLJ DĞƐƐĂŐĞ WƌŽďĂďůĞĂƵƐĞͬǀĞŶƚ ŽƌƌĞĐƚŝǀĞĐƚŝŽŶƐ
0010
Mow
Overheat
Ͳ
The mowing motor has been working under a
severe load for too long.
Ͳ
No need for action – the unit will renew automatically
the operation after the mowing motor will cool down.
0011
Drive Overheat
Ͳ The drive motors have been working under a
severe load for too long
͘
Ͳ
No need to do anything.
Ͳ The unit will renew the operation automatically as
soon as the drive motor will cool down.
0012
No wire signal
Ͳ See E3 in the above table
0014
Front wheel
problem
Ͳ
See E7 in the above table
0015
Button pressed
Ͳ One of the operating panel buttons is constantly
pressed.
Ͳ
Press 'OK' to confirm the message and continue
operation. This message is displayed to inform only
͘
0016
Low
temperature
Ͳ Mower does not depart automatically from the
Base Station when the ambiance temperature is
lower than 5ºC (41ºF).
Ͳ
Information - When the temperature is below 5ºC
(41ºF) the grass does not grow or grows very
slowly.
However Manual Depart is enabled
͘
Ͳ No need to do anything.
Ͳ
The unit will renew the operation automatically as
soon as the ambiance temperature will rise above 5ºC
(41ºF).
0020
Rain detected
Ͳ The operation is delayed as the unit detects rain.
Ͳ No need for action.
Ͳ
The message is displayed until the unit will not detect
rain and then will start mowing
͘
0021
Check mowing
height
Ͳ Mowing motor has faced over-current
conditions for too long as a result of high grass
or an obstacle that is stuck or wrapped around the
blade.
Ͳ Something is preventing a blade from rotating
freely.
Severe grass accumulation under the mowing
deck, rope, or similar object is wrapped around
mowing blade.
Ͳ CAUTION – Switch Off the Safety Switch before
checking the blade.
Ͳ Inspect the blade for foreign material or debris
preventing rotation.
Ͳ Clean out accumulated grass clippings using a wooden
stick.
0022
Check mowing
motor
Ͳ Mowing motor has faced over-current for too
long in the Base Station before starting the
operation.
Ͳ
CAUTION – Switch Off the Safety Switch before
checking the blade.
Ͳ Remove the mower from the Base Station. Inspect the
blade for foreign material or debris preventing rotation
͘
0023
Check power
Ͳ
See E4 in the above table
0026
Base problem
Ͳ
The unit fails to enter the Base Station several
consecutive times.
Ͳ
Adjust the Base Station position.
Ͳ
Clean the contacts with a brush or piece of cloth.
0027
Start Elsewhere
Ͳ
Drive wheel motors have been working under
severe load during automatic or manual
operation
͘
Ͳ Check to insure the mower is not stuck, causing the
drive wheels to slip.
Ͳ Check the ground around the mower for holes or
indentations. Fill with dirt and level off.
Ͳ Check if the drive wheels are free to rotate and nothing
is blocking them.
Ͳ
Remove the mower away from this particular location
and restart operation
͘
0028
Cross Outside
Ͳ
The Perimeter Wire is too close to the edge.
Ͳ
The lawn slope is too big.
Ͳ
The unit does not succeed to turn in place at the
edge and it causes the mower to slip out of the
designated area.
Ͳ
The unit has slipped out of the Perimeter Wire
lope because of sloping area or wet grass.
Ͳ
Remove the wire towards the inner part of the lawn.
Ͳ
Do not include this area because of its steep slopes.
Ͳ
Fill holes and pits in the ground.
Ͳ Increase the cutting height ͘
80
en